15 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Not listed in our catalog? You are welcome to submit your requirements. We assess whether our equipment, production lines and process capabilities suit your grade, product form, dimensions, processing and delivery requirements, then discuss possible processing, trials or supply arrangements.
Feasibility and supply terms are confirmed after technical review. The standard information on this page is not a supply or performance commitment.
Keep your entries and try again later, or contact website@chqwire.net. If you have already received confirmation, do not submit again.
X2CrNiMoN17-13-3 · EN 10263-5-2001
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material category
Stainless steel
Subcategory
Austenitic stainless steel
Material form
Reference record
Original record status
Original standard verified
Standard edition
EN 10263-5-2001
Table / clause
Table 2 and notes a–e; Table 3 is cited only for deviations
PDF page references
1、8、9
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e.
Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges.
Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use.
This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options.
For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti.
The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Original condition-branch records
Default heat-analysis values in historical Table 2
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotes
X2CrNiMoN17-13-3 · ISO 4954
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Ni
10.5 ～ 13
Mo
2.5 ～ 3
N
0.12 ～ 0.22
Cu
≤ 1 (lower limit not stated)
Applicability and limitations
Composition based on ISO 4954:2018; the product edition is unspecified, so confirm the edition applicable to the contract.
Composition conditions
ISO 4954:2018, Table D.2 gives heat analysis; A single value is a maximum; a dash is not zero.
Product-analysis tolerances are listed separately under Table 2/3 of the standard and do not directly widen the heat-analysis composition ranges.
Unlisted elements must not be intentionally added without purchaser consent, except for additions needed to finish the heat.
Verification notes
Composition based on ISO 4954:2018; the product edition is unspecified, so confirm the edition applicable to the contract.View associated products →
X2CrNiMoN17-13-3 · ISO 4954-2018
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material category
Stainless steel
Subcategory
Stainless steel
Material form
Reference record
Original record status
Original standard verified
Standard edition
ISO 4954:2018
Table / clause
Table D.2
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Ni
10.5 ～ 13
Mo
2.5 ～ 3
N
0.12 ～ 0.22
Cu
≤ 1 (lower limit not stated)
Applicability and limitations
ISO 4954:2018 Table D.2 gives cast analysis; single values are maxima and dashes are not zero.
Product-analysis deviations are listed separately under Tables 2/3, not used directly to relax cast-composition limits.
Elements not listed must not be intentionally added without the purchaser's consent, except for finishing the heat.
Verification notes
The original standard, Table D.2 and footnotes have been checked
X2CrNiMoN17-13-3 · EN 10263-5-2017
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
EN 10263-5-2017
Table / clause
Table 3 and footnotes a–e
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Applicability and limitations
Heat-analysis mass fractions wt%; Product-analysis tolerances follow Table 4 separately. ; The sulfur conditions for machining, welding and polishing in Table 3, note b are retained separately; different requirements are not imposed simultaneously. ; Ti-stabilized grades require 5×C≤Ti≤0.70%, checked jointly with measured C/Ti. ; This standard covers stainless steel for cold heading and cold extrusion; delivery condition, dimensions, surface and mechanical properties still require independent confirmation. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; unspecified contents are not treated as zero.
Original condition-branch records
Default composition in Table 3
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Verification notes
The original English Table 3 and footnotes have been checked
X2CrNiMoN17-13-3 · EN 10269-2013
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
EN 10269-2013
Table / clause
Table 1 and notes a–c
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Applicability and limitations
Heat-analysis mass fractions wt%; Product-analysis tolerances require separate verification under Table 2. ; The agreed sulfur condition in Table 1, note b applies only to grades marked b; default, machining and welding ranges are retained separately. ; This standard covers steels and nickel alloys for high- and low-temperature fasteners; cold-heading suitability is not established for every grade or delivery condition. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; Unspecified values are not treated as zero.
Verification notes
The original English Table 1 and footnotes were checked
X2CrNiMoN17-13-3 · NF EN 10269-1999
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
NF EN 10269-1999
Table / clause
Table 1 · Notes 1/2
PDF page references
23
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 1 default S≤.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Recommended S .015–.030% to improve machinability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1 (lower limit not stated)
Mn
≤ 2 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.5 ～ 18.5
Ni
11 ～ 14
N
0.12 ～ 0.22
Mo
2.5 ～ 3
Applicability and limitations
Original text NF EN10269 cover novembre1999, Table 1 heat analysis mass fraction %. ; Table 1, Note 2: Sulfur .015–.030% is a recommended range for improved machinability; it does not replace the default maximum.; This note does not apply to 42CrMo4 as it is not marked. ; Elements not listed shall not be intentionally added without the purchaser's consent (except additions needed to finish steelmaking); blanks are not zero. ; Standards for high- and low-temperature fastener steels and nickel alloys; Composition alone does not prove that cold-heading wire is available or suitable for forming. ; Product-analysis deviations require separate verification under Table 2; they do not expand the default heat-analysis range.; Sulfur limits of the 2013 version do not apply.
Original condition-branch records
Table 1 default S≤.030%
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1 (lower limit not stated)
Mn
≤ 2 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.5 ～ 18.5
Ni
11 ～ 14
N
0.12 ～ 0.22
Mo
2.5 ～ 3
Recommended S .015–.030% to improve machinability
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1 (lower limit not stated)
Mn
≤ 2 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
Cr
16.5 ～ 18.5
Ni
11 ～ 14
N
0.12 ～ 0.22
Mo
2.5 ～ 3
A condition branch must be selected
Yes
Verification notes
Values and notes in original NF, Table 1 were visually checked
X2CrNiMoN17-13-3 · EN 10269-2006
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Historical-edition reference
Standard edition
NF EN 10269-1999
Table / clause
Table 1 · Notes 1/2
PDF page references
23
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 1 default S≤.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Recommended S .015–.030% to improve machinability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1 (lower limit not stated)
Mn
≤ 2 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.5 ～ 18.5
Ni
11 ～ 14
N
0.12 ～ 0.22
Mo
2.5 ～ 3
Applicability and limitations
The chemical composition currently shown is transcribed from the original NF EN 10269-1999; The original record cites EN 10269-2006; that original edition remains unavailable, and differences between editions have not been confirmed. Original text NF EN10269 cover novembre1999, Table 1 heat analysis mass fraction %. ; Table 1, Note 2: Sulfur .015–.030% is a recommended range for improved machinability; it does not replace the default maximum.; This note does not apply to 42CrMo4 as it is not marked. ; Elements not listed shall not be intentionally added without the purchaser's consent (except additions needed to finish steelmaking); blanks are not zero. ; Standards for high- and low-temperature fastener steels and nickel alloys; Composition alone does not prove that cold-heading wire is available or suitable for forming. ; Product-analysis deviations require separate verification under Table 2; they do not expand the default heat-analysis range.; Sulfur limits of the 2013 version do not apply.
Original condition-branch records
Table 1 default S≤.030%
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1 (lower limit not stated)
Mn
≤ 2 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.5 ～ 18.5
Ni
11 ～ 14
N
0.12 ～ 0.22
Mo
2.5 ～ 3
Recommended S .015–.030% to improve machinability
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1 (lower limit not stated)
Mn
≤ 2 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
Cr
16.5 ～ 18.5
Ni
11 ～ 14
N
0.12 ～ 0.22
Mo
2.5 ～ 3
A condition branch must be selected
Yes
Verification notes
The chemical composition currently shown is transcribed from the original NF EN 10269-1999; The original record cites EN 10269-2006; that original edition remains unavailable, and differences between editions have not been confirmed.
X2CrNiMoN17-13-3 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
DIN EN 10263-5-2002
Table / clause
Table 2 and notes a–e; Table 3 is cited only for deviations
PDF page references
1、8、9
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e.
Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges.
Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use.
This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options.
For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti.
The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Original condition-branch records
Default heat-analysis values in historical Table 2
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotes
X2CrNiMoN17-13-3 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
DIN EN 10263-5-2002
Table / clause
Table 2 and notes a–e; Table 3 is cited only for deviations
PDF page references
1、8、9
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e.
Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges.
Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use.
This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options.
For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti.
The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Original condition-branch records
Default heat-analysis values in historical Table 2
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotes
X2CrNiMoN17-13-3 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
EN 10088-1-2005
Table / clause
Table 4 and continuation; notes a–e; all 50 austenitic corrosion-resistant steel grades
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Applicability and limitations
EN 10088-1:2005 Table 4 and continuation: ladle analysis (wt%); the official SIST adoption preview PDF, pages 11/12, covers all 50 grades and notes. Note a: unlisted elements are not intentionally added without purchaser consent, except as needed to complete steelmaking; a blank is not zero. Note b: for grades marked b only, S is selected separately for long products and by property requirement. Note d: the increased Ni maximum for special reasons applies only to listed grades, not all grades. Note c: Cu up to 1.0% for cold heading/extrusion; this condition path is provided here only for grades with blank Cu in the original table. Existing Cu alloy ranges retain their original values; the exception has not automatically rewritten them. The linked Ti≥5C/Nb≥10C and Ti≥8(C+N) conditions are retained; an unlisted N maximum is not zero. Note e: the source warns of skin-contact regulatory issues for high-sulfur free-machining steel; this is retained as a historical warning only and is not a claim of current compliance based on the 2005 text. Listed chemistry and the cold-heading Cu exception alone do not establish overall cold-heading performance or company supply; mechanical and product standards must be checked separately, and national adoption does not mean automatic equivalence.
Original condition-branch records
Default sulfur requirement; default Ni; the cold-heading Cu exception is not selected, so the original-table Cu requirement applies.
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
A condition branch must be selected
Yes
Verification notes
Official source Table 4, all 50 rows and footnotes visually checked; conditional route for Cu cells left blank in the original.
X2CrNiMoN17-13-3 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
EN 10088-1-2005
Table / clause
Table 4 and continuation; notes a–e; all 50 austenitic corrosion-resistant steel grades
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Applicability and limitations
EN 10088-1:2005 Table 4 and continuation: ladle analysis (wt%); the official SIST adoption preview PDF, pages 11/12, covers all 50 grades and notes. Note a: unlisted elements are not intentionally added without purchaser consent, except as needed to complete steelmaking; a blank is not zero. Note b: for grades marked b only, S is selected separately for long products and by property requirement. Note d: the increased Ni maximum for special reasons applies only to listed grades, not all grades. Note c: Cu up to 1.0% for cold heading/extrusion; this condition path is provided here only for grades with blank Cu in the original table. Existing Cu alloy ranges retain their original values; the exception has not automatically rewritten them. The linked Ti≥5C/Nb≥10C and Ti≥8(C+N) conditions are retained; an unlisted N maximum is not zero. Note e: the source warns of skin-contact regulatory issues for high-sulfur free-machining steel; this is retained as a historical warning only and is not a claim of current compliance based on the 2005 text. Listed chemistry and the cold-heading Cu exception alone do not establish overall cold-heading performance or company supply; mechanical and product standards must be checked separately, and national adoption does not mean automatic equivalence.
Original condition-branch records
Default sulfur requirement; default Ni; the cold-heading Cu exception is not selected, so the original-table Cu requirement applies.
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
A condition branch must be selected
Yes
Verification notes
Official source Table 4, all 50 rows and footnotes visually checked; conditional route for Cu cells left blank in the original.
X2CrNiMoN17-13-3 · NF EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Composition basis in the adopted standard verified
Standard edition
EN 10088-1-2005
Table / clause
Table 4 and continuation; notes a–e; all 50 austenitic corrosion-resistant steel grades
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Applicability and limitations
NF EN 10088-1:2005 adopts EN 10088-1:2005 (EN 10088-1-2005); See the data basis for the actual composition source file and table number. EN10088-1:2005 Table 4 and its continuation; heat analysis wt%; all 50 grades and footnotes on PDF pages 11/12 of the official SIST adoption preview.. ; Note a: Elements not listed shall not be intentionally added without the consent of the purchaser (except additions needed to finish steelmaking).; Blanks are not entered as zero. ; Note b: For grades marked b, S shall be selected separately according to long products and properties.; The increased Ni upper limit based on special reasons in Note d applies only to the listed steel grades and cannot be generalized to all grades.. ; Note c: For cold-heading/cold-extrusion applications, Cu max 1.0%.; This conditional path is provided only for grades where Cu was blank in the original table; existing Cu alloying ranges shall retain their original values, and their Cu exceptions have not been automatically rewritten.. ; The linkages Ti≥5C/Nb≥10C and Ti≥8(C+N) are retained.; If no N upper limit is listed, do not fill as zero.. ; Note e retains the original historical caution about skin-contact regulations for high-sulfur free-cutting steel; the 2005 text is not used to claim present-day compliance.. ; The listed compositions and the cold-heading Cu exception do not independently prove the overall cold-heading properties of the material or company supply.; Mechanical properties and product standards require separate verification; national adoption does not automatically establish equivalence..
Original condition-branch records
Default sulfur requirement; default Ni; the cold-heading Cu exception is not selected, so the original-table Cu requirement applies.
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.015 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
0.008 ～ 0.03
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
Cu
≤ 1.0 (lower limit not stated)
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
N
0.12 ～ 0.22
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 15.0
Cu
≤ 1.0 (lower limit not stated)
A condition branch must be selected
Yes
Verification notes
The formal adoption relationship and corresponding EN composition original have been checked; the complete national adoption text has not been verified page by page.
X2CrNiMoN17-13-3 · NF EN 10269:1999
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material category
Stainless steel
Subcategory
Stainless steel
Material form
Reference record
Original record status
Original-standard record
Standard edition
NF EN 10269:1999
Table / clause
EN 10269:1999 Table 1 and footnotes 1 and 2
PDF page references
2、23
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Applicability and limitations
The cover of NF EN 10269:1999 explicitly adopts EN 10269:1999; Preserve the correspondence between the French adoption version and the European version; do not label as other countries or new editions. ; Table 1 gives heat-analysis mass percentages; Single values in P and S columns are upper limits; other single values are parsed according to the inequality signs in the original table; Unspecified elements shall not be filled as zero. ; Applies to billets, bars and wire rod of steels and nickel alloys for fasteners with specified high- or low-temperature properties.; Cold heading and actual supply must be verified in conjunction with delivery condition, dimensions, and process. ; Table 1 Footnote 1: Elements not listed in the table shall not be intentionally added without the buyer's consent (except additions needed to finish steelmaking); Elements that affect properties must be prevented from being introduced via scrap steel, etc.. ; This record only verifies the heat analysis composition in Table 1; product analysis tolerances in Table 2 shall not be automatically added to the heat limits. ; Footnote 2 of Table 1 only suggests controlling S within 0.015–0.030% to improve machinability; The suggested value shall not be treated as a mandatory S lower limit; the default remains S≤0.030%.
Combined limits
Combined-element limits
X2CrNiMoN17-13-3 · DIN EN 10263-5-2018
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
DIN EN 10263-5:2018-02
Table / clause
Tabelle 3 and footnote a–e; Tabelle 4 product-analysis tolerances require separate verification
PDF page references
1、10、11
Unit
Mass fraction (wt%)
Analysis type
Heat analysis
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Applicability and limitations
DIN EN 10263-5:2018-02 is the German-language edition of EN 10263-5:2017; This record was verified against heat analysis and footnotes in Table 3 of the official German edition. ; Heat-analysis mass fractions wt%; Product-analysis tolerances follow Table 4 separately. ; The sulfur conditions for machining, welding and polishing in Table 3, note b are retained separately; different requirements are not imposed simultaneously. ; Ti-stabilized grades require 5×C≤Ti≤0.70%, checked jointly with measured C/Ti. ; This standard covers stainless steel for cold heading and cold extrusion; delivery condition, dimensions, surface and mechanical properties still require independent confirmation. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; unspecified contents are not treated as zero.
Original condition-branch records
Default composition in Table 3
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 2.0 (lower limit not stated)
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.5 ～ 18.5
Mo
2.5 ～ 3.0
Ni
11.0 ～ 14.0
N
0.12 ～ 0.22
Cu
≤ 1.0 (lower limit not stated)
Verification notes
DIN EN 10263-5:2018-02 official German edition, Table 3, row 11 and notes a–e checked; adopts EN 10263-5:2017.
X2CrNiMoN17-13-3 · EN 10263
Original-source verification is incomplete; this is not a formal standard reference
Material category
Stainless steel
Subcategory
Stainless steel
Material form
Drawn wire
Verification status
Published on the website; original-source verification pending
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
Element
Composition requirement
C
≤ 0.03 (lower limit not stated)
Cr
16.5 ～ 18.5
Cu
≤ 1 (lower limit not stated)
Mn
≤ 2 (lower limit not stated)
Mo
2.5 ～ 3
N
0.12 ～ 0.22
Ni
11 ～ 14
P
≤ 0.045 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Si
≤ 1 (lower limit not stated)
Applicability and limitations
Give priority to the published technical page on the Creation Group website. Use local reference ranges only as supplementary composition cross-checks; the applicable standard for that product page, the technical agreement and actual verification take precedence.
