X12CR13
13 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for X12CR13 →Material demand assessment
Looking for X12CR13 material?
Related catalog information is available. New material and processing requirements are also welcome. We assess whether our equipment, production lines and process capabilities suit your grade, product form, dimensions, processing and delivery requirements, then discuss possible processing, trials or supply arrangements.
Feasibility and supply terms are confirmed after technical review. The standard information on this page is not a supply or performance commitment.
Keep your entries and try again later, or contact website@chqwire.net. If you have already received confirmation, do not submit again.
X12Cr13 · ISO 4954
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Stainless steel
- Subcategory
- Stainless steel
- Material form
- Cold-heading wire
- Original record status
- Source edition identified; composition verification pending
- Standard edition
- ISO 4954:2018
- Table / clause
- Table D.2
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
Composition based on ISO 4954:2018; the product edition is unspecified, so confirm the edition applicable to the contract.
Composition conditions
- ISO 4954:2018, Table D.2 gives heat analysis; A single value is a maximum; a dash is not zero.
- Product-analysis tolerances are listed separately under Table 2/3 of the standard and do not directly widen the heat-analysis composition ranges.
- Unlisted elements must not be intentionally added without purchaser consent, except for additions needed to finish the heat.
Verification notes
Composition based on ISO 4954:2018; the product edition is unspecified, so confirm the edition applicable to the contract.View associated products →X12Cr13 · ISO 4954-2018
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Stainless steel
- Subcategory
- Stainless steel
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- ISO 4954:2018
- Table / clause
- Table D.2
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
ISO 4954:2018 Table D.2 gives cast analysis; single values are maxima and dashes are not zero.
Product-analysis deviations are listed separately under Tables 2/3, not used directly to relax cast-composition limits.
Elements not listed must not be intentionally added without the purchaser's consent, except for finishing the heat.
Verification notes
The original standard, Table D.2 and footnotes have been checkedX12Cr13 · EN 10263-5-2017
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10263-5-2017
- Table / clause
- Table 3 and footnotes a–e
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default composition in Table 3
Machinability condition S 0.015–0.030%
Weldability condition S 0.008–0.030%
Polishability recommendation S≤0.015%
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
Heat-analysis mass fractions wt%; Product-analysis tolerances follow Table 4 separately. ; The sulfur conditions for machining, welding and polishing in Table 3, note b are retained separately; different requirements are not imposed simultaneously. ; Ti-stabilized grades require 5×C≤Ti≤0.70%, checked jointly with measured C/Ti. ; This standard covers stainless steel for cold heading and cold extrusion; delivery condition, dimensions, surface and mechanical properties still require independent confirmation. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; unspecified contents are not treated as zero.
Original condition-branch records
Default composition in Table 3
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Machinability condition S 0.015–0.030%
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Weldability condition S 0.008–0.030%
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Polishability recommendation S≤0.015%
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
The original English Table 3 and footnotes have been checkedX12Cr13 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- DIN EN 10263-5-2002
- Table / clause
- Table 2 and notes a–e; Table 3 is cited only for deviations
- PDF page references
- 1、8、9
Carbon-equivalent reference
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
The original webpage states DIN EN 10263-5-2018; The composition in this record was actually verified against DIN EN 10263-5-2002; the edition is now identified as 2002 according to the original evidence; See the separate complete-table record for edition 2018. ; Source actually used: DIN EN10263-5:2002-02, the German-language adoption of EN10263-5:2001; PDF8, Table 2 and notes a–e. ; Default heat analysis in wt%.; Apply product-analysis tolerances in Table 3 separately; do not add them to the default heat-analysis range. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; Residual elements must not impair the properties or intended use. ; The older table does not use the 2017 edition’s separate sulfur conditions; do not copy machining/welding/polishing options from the newer edition.. ; For Ti-stabilized grades, check 5×C≤Ti≤0.70% against measured C.; Does not apply to grades for which Ti is not specified. ; Standard range for cold-heading and cold-extrusion; actual supply, dimensions, delivery condition, and performance still require confirmation..
Original condition-branch records
Default heat-analysis values in historical Table 2
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Verification notes
The original webpage states DIN EN 10263-5-2018; The composition in this record was actually verified against DIN EN 10263-5-2002; the edition is now identified as 2002 according to the original evidence; See the separate complete-table record for edition 2018.X12Cr13 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- DIN EN 10263-5-2002
- Table / clause
- Table 2 and notes a–e; Table 3 is cited only for deviations
- PDF page references
- 1、8、9
Carbon-equivalent reference
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e. / Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges. / Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use. / This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options. / For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti. / The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.Composition conditions
- Source actually used: DIN EN10263-5:2002-02, the German-language adoption of EN10263-5:2001; PDF8, Table 2 and notes a–e.
- Default heat analysis in wt%.; Apply product-analysis tolerances in Table 3 separately; do not add them to the default heat-analysis range.
- Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; Residual elements must not impair the properties or intended use.
- The older table does not use the 2017 edition’s separate sulfur conditions; do not copy machining/welding/polishing options from the newer edition..
- For Ti-stabilized grades, check 5×C≤Ti≤0.70% against measured C.; Does not apply to grades for which Ti is not specified.
- Standard range for cold-heading and cold-extrusion; actual supply, dimensions, delivery condition, and performance still require confirmation..
Original condition-branch records
Default heat-analysis values in historical Table 2
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotesX12Cr13 · EN 10263-5-2001
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10263-5-2001
- Table / clause
- Table 2 and notes a–e; Table 3 is cited only for deviations
- PDF page references
- 1、8、9
Carbon-equivalent reference
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e.
Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges.
Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use.
This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options.
For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti.
The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Original condition-branch records
Default heat-analysis values in historical Table 2
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotesX12Cr13 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- DIN EN 10263-5-2002
- Table / clause
- Table 2 and notes a–e; Table 3 is cited only for deviations
- PDF page references
- 1、8、9
Carbon-equivalent reference
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e. / Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges. / Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use. / This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options. / For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti. / The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.Composition conditions
- Source actually used: DIN EN10263-5:2002-02, the German-language adoption of EN10263-5:2001; PDF8, Table 2 and notes a–e.
- Default heat analysis in wt%.; Apply product-analysis tolerances in Table 3 separately; do not add them to the default heat-analysis range.
- Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; Residual elements must not impair the properties or intended use.
- The older table does not use the 2017 edition’s separate sulfur conditions; do not copy machining/welding/polishing options from the newer edition..
- For Ti-stabilized grades, check 5×C≤Ti≤0.70% against measured C.; Does not apply to grades for which Ti is not specified.
- Standard range for cold-heading and cold-extrusion; actual supply, dimensions, delivery condition, and performance still require confirmation..
Original condition-branch records
Default heat-analysis values in historical Table 2
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotesX12Cr13 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 3 and continuation, notes a–d; all 30 martensitic and precipitation-hardening corrosion-resistant steel grades
- PDF page references
- 1、3、9、10
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
Note b recommends and permits S .015–.030 for machinability
Note b recommends and permits S .008–.030 for weldability
Note b recommends S≤.015 for polishability
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
EN10088-1:2005, Table 3 including its continuation, heat analysis wt%; official English SIST adoption preview PDF9/10. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; blanks are not filled with zero or a general residual maximum. ; Note b distinguishes sulfur conditions for long products, machining, welding and polishing only for grades marked b; it is not extended to all grades. ; Note c: a narrower C range may be agreed at enquiry and ordering; Without a contract, the original table range is not replaced. ; Note d: only for X7CrNiAl17-7 to improve cold-deformation performance, the Ni maximum is 8.3%; select separately from default 7.8. ; A designation-list standard does not independently establish cold-heading suitability, mechanical-property delivery requirements or product supply; Adopted editions such as NF/DIN are not automatically verified by this European main text.
Original condition-branch records
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b recommends and permits S .015–.030 for machinability
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b recommends and permits S .008–.030 for weldability
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b recommends S≤.015 for polishability
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
All 30 rows of Table 3 and footnotes visually checked.X12Cr13 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 3 and continuation, notes a–d; all 30 martensitic and precipitation-hardening corrosion-resistant steel grades
- PDF page references
- 1、3、9、10
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
Note b recommends and permits S .015–.030 for machinability
Note b recommends and permits S .008–.030 for weldability
Note b recommends S≤.015 for polishability
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
EN10088-1:2005, Table 3 including its continuation, heat analysis wt%; official English SIST adoption preview PDF9/10. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; blanks are not filled with zero or a general residual maximum. ; Note b distinguishes sulfur conditions for long products, machining, welding and polishing only for grades marked b; it is not extended to all grades. ; Note c: a narrower C range may be agreed at enquiry and ordering; Without a contract, the original table range is not replaced. ; Note d: only for X7CrNiAl17-7 to improve cold-deformation performance, the Ni maximum is 8.3%; select separately from default 7.8. ; A designation-list standard does not independently establish cold-heading suitability, mechanical-property delivery requirements or product supply; Adopted editions such as NF/DIN are not automatically verified by this European main text.
Original condition-branch records
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b recommends and permits S .015–.030 for machinability
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b recommends and permits S .008–.030 for weldability
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b recommends S≤.015 for polishability
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
All 30 rows of Table 3 and footnotes visually checked.X12Cr13 · NF EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Composition basis in the adopted standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 3 and continuation, notes a–d; all 30 martensitic and precipitation-hardening corrosion-resistant steel grades
- PDF page references
- 1、3、9、10
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
Note b recommends and permits S .015–.030 for machinability
Note b recommends and permits S .008–.030 for weldability
Note b recommends S≤.015 for polishability
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
NF EN 10088-1:2005 adopts EN 10088-1:2005 (EN 10088-1-2005); See the data basis for the actual composition source file and table number. EN10088-1:2005, Table 3 including its continuation, heat analysis wt%; official English SIST adoption preview PDF9/10. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; blanks are not filled with zero or a general residual maximum. ; Note b distinguishes sulfur conditions for long products, machining, welding and polishing only for grades marked b; it is not extended to all grades. ; Note c: a narrower C range may be agreed at enquiry and ordering; Without a contract, the original table range is not replaced. ; Note d: only for X7CrNiAl17-7 to improve cold-deformation performance, the Ni maximum is 8.3%; select separately from default 7.8. ; A designation-list standard does not independently establish cold-heading suitability, mechanical-property delivery requirements or product supply; Adopted editions such as NF/DIN are not automatically verified by this European main text.
Original condition-branch records
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b recommends and permits S .015–.030 for machinability
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b recommends and permits S .008–.030 for weldability
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Note b recommends S≤.015 for polishability
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
The formal adoption relationship and corresponding EN composition original have been checked; the complete national adoption text has not been verified page by page.X12Cr13 · ISO 15510-2014
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Stainless steel
- Subcategory
- Stainless steel
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- ISO 15510-2014
- Table / clause
- The current grade row in Table1; Note a and corresponding footnotes (original text on the publishing platform)
- PDF page references
- 15
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
ISO 15510:2014, Table 1 gives heat analysis, mass fractions wt%; Under note a, values without a stated range or minimum are maxima; a dash is not treated as zero. Composition rows follow an excerpt of the official PDF edition; relevant footnotes follow the original Table 1 in the Sample text section of the standards publishing platform; Verification of the complete standard text or mechanical properties is not claimed. The standard covers material for wrought products, including ingots and semi-finished products; Similar composition does not establish direct substitution; cold-heading suitability and supply condition require separate confirmation. The S 0.015–0.030% machinability recommendations, 0.008–0.020% weldability recommendation and S≤0.015% polishability recommendation in note b concern specific properties and do not directly replace this row’s sulfur limits.
Verification notes
The row for this grade in Table 1 has been checked against the official PDF; Relevant original footnotes are retained in the supporting verification record; Full standard text and mechanical properties to be verified separatelyX12Cr13 · DIN EN 10263-5-2018
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- DIN EN 10263-5:2018-02
- Table / clause
- Tabelle 3 and footnote a–e; Tabelle 4 product-analysis tolerances require separate verification
- PDF page references
- 1、10、11
- Unit
- Mass fraction (wt%)
- Analysis type
- Heat analysis
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default composition in Table 3
Machinability condition S 0.015–0.030%
Weldability condition S 0.008–0.030%
Polishability recommendation S≤0.015%
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Applicability and limitations
DIN EN 10263-5:2018-02 is the German-language edition of EN 10263-5:2017; This record was verified against heat analysis and footnotes in Table 3 of the official German edition. ; Heat-analysis mass fractions wt%; Product-analysis tolerances follow Table 4 separately. ; The sulfur conditions for machining, welding and polishing in Table 3, note b are retained separately; different requirements are not imposed simultaneously. ; Ti-stabilized grades require 5×C≤Ti≤0.70%, checked jointly with measured C/Ti. ; This standard covers stainless steel for cold heading and cold extrusion; delivery condition, dimensions, surface and mechanical properties still require independent confirmation. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; unspecified contents are not treated as zero.
Original condition-branch records
Default composition in Table 3
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Machinability condition S 0.015–0.030%
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Weldability condition S 0.008–0.030%
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
Polishability recommendation S≤0.015%
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 11.5 ～ 13.5 |
| Ni | ≤ 0.75 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
DIN EN 10263-5:2018-02 official German edition, Table 3, row 19 and notes a–e checked; adopts EN 10263-5:2017.X12Cr13 · EN 10263
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Stainless steel
- Material form
- Drawn wire
- Verification status
- Published on the website; original-source verification pending
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | 0.08 ～ 0.15 |
| Cr | 11.5 ～ 13.5 |
| Mn | ≤ 1.5 (lower limit not stated) |
| Ni | ≤ 0.75 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
Give priority to the published technical page on the Creation Group website. Use local reference ranges only as supplementary composition cross-checks; the applicable standard for that product page, the technical agreement and actual verification take precedence.