13 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Related catalog information is available. New material and processing requirements are also welcome. We assess whether our equipment, production lines and process capabilities suit your grade, product form, dimensions, processing and delivery requirements, then discuss possible processing, trials or supply arrangements.
Feasibility and supply terms are confirmed after technical review. The standard information on this page is not a supply or performance commitment.
Keep your entries and try again later, or contact website@chqwire.net. If you have already received confirmation, do not submit again.
X6Cr17 · EN 10263-5-2001
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material category
Stainless steel
Subcategory
Ferritic stainless steel
Material form
Reference record
Original record status
Original standard verified
Standard edition
EN 10263-5-2001
Table / clause
Table 2 and notes a–e; Table 3 is cited only for deviations
PDF page references
1、8、9
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default heat-analysis values in historical Table 2
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: C≤0.04% agreed at enquiry or ordering to improve cold formability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e.
Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges.
Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use.
This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options.
For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti.
The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Original condition-branch records
Default heat-analysis values in historical Table 2
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b: C≤0.04% agreed at enquiry or ordering to improve cold formability
Element
Composition requirement
C
≤ 0.04 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
A condition branch must be selected
Yes
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotes
X6Cr17 · ISO 4954
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16 ～ 18
Applicability and limitations
Composition based on ISO 4954:2018; the product edition is unspecified, so confirm the edition applicable to the contract.
Composition conditions
ISO 4954:2018, Table D.2 gives heat analysis; A single value is a maximum; a dash is not zero.
Product-analysis tolerances are listed separately under Table 2/3 of the standard and do not directly widen the heat-analysis composition ranges.
Unlisted elements must not be intentionally added without purchaser consent, except for additions needed to finish the heat.
Note e recommends agreed C≤0.04% in the order to improve cold formability; the tabulated requirement remains C≤0.08%.
Verification notes
Composition based on ISO 4954:2018; the product edition is unspecified, so confirm the edition applicable to the contract.View associated products →
X6Cr17 · ISO 4954-2018
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material category
Stainless steel
Subcategory
Stainless steel
Material form
Reference record
Original record status
Original standard verified
Standard edition
ISO 4954:2018
Table / clause
Table D.2
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16 ～ 18
Applicability and limitations
ISO 4954:2018, Table D.2 gives heat analysis; A single value is a maximum; a dash is not zero. ; Product-analysis tolerances are listed separately under Table 2/3 of the standard and do not directly widen the heat-analysis composition ranges. ; Unlisted elements must not be intentionally added without purchaser consent, except for additions needed to finish the heat. ; Note e recommends agreed C≤0.04% in the order to improve cold formability; the tabulated requirement remains C≤0.08%.
Verification notes
The original standard, Table D.2 and footnotes have been checked
X6Cr17 · EN 10263-5-2017
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
EN 10263-5-2017
Table / clause
Table 3 and footnotes a–e
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default composition in Table 3
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Machinability condition S 0.015–0.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Weldability condition S 0.008–0.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Polishability recommendation S≤0.015%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default composition in Table 3; Agreed cold-forming C≤0.04%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Machinability condition S 0.015–0.030%; Agreed cold-forming C≤0.04%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Weldability condition S 0.008–0.030%; Agreed cold-forming C≤0.04%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
Heat-analysis mass fractions wt%; Product-analysis tolerances follow Table 4 separately. ; The sulfur conditions for machining, welding and polishing in Table 3, note b are retained separately; different requirements are not imposed simultaneously. ; Ti-stabilized grades require 5×C≤Ti≤0.70%, checked jointly with measured C/Ti. ; This standard covers stainless steel for cold heading and cold extrusion; delivery condition, dimensions, surface and mechanical properties still require independent confirmation. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; unspecified contents are not treated as zero. ; Note c: C≤0.04% may be agreed at enquiry or ordering to improve cold formability; Default tabulated limit ≤0.08%.
Original condition-branch records
Default composition in Table 3
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Machinability condition S 0.015–0.030%
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.015 ～ 0.03
Cr
16.0 ～ 18.0
Weldability condition S 0.008–0.030%
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.008 ～ 0.03
Cr
16.0 ～ 18.0
Polishability recommendation S≤0.015%
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
Default composition in Table 3; Agreed cold-forming C≤0.04%
Element
Composition requirement
C
≤ 0.04 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Machinability condition S 0.015–0.030%; Agreed cold-forming C≤0.04%
Element
Composition requirement
C
≤ 0.04 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.015 ～ 0.03
Cr
16.0 ～ 18.0
Weldability condition S 0.008–0.030%; Agreed cold-forming C≤0.04%
The original English Table 3 and footnotes have been checked
X6Cr17 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
DIN EN 10263-5-2002
Table / clause
Table 2 and notes a–e; Table 3 is cited only for deviations
PDF page references
1、8、9
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default heat-analysis values in historical Table 2
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: C≤0.04% agreed at enquiry or ordering to improve cold formability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
The original webpage states DIN EN 10263-5-2018; The composition in this record was actually verified against DIN EN 10263-5-2002; the edition is now identified as 2002 according to the original evidence; See the separate complete-table record for edition 2018. ; Source actually used: DIN EN10263-5:2002-02, the German-language adoption of EN10263-5:2001; PDF8, Table 2 and notes a–e. ; Default heat analysis in wt%.; Apply product-analysis tolerances in Table 3 separately; do not add them to the default heat-analysis range. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; Residual elements must not impair the properties or intended use. ; The older table does not use the 2017 edition’s separate sulfur conditions; do not copy machining/welding/polishing options from the newer edition.. ; For Ti-stabilized grades, check 5×C≤Ti≤0.70% against measured C.; Does not apply to grades for which Ti is not specified. ; Standard range for cold-heading and cold-extrusion; actual supply, dimensions, delivery condition, and performance still require confirmation..
Original condition-branch records
Default heat-analysis values in historical Table 2
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b: C≤0.04% agreed at enquiry or ordering to improve cold formability
Element
Composition requirement
C
≤ 0.04 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
A condition branch must be selected
Yes
Verification notes
The original webpage states DIN EN 10263-5-2018; The composition in this record was actually verified against DIN EN 10263-5-2002; the edition is now identified as 2002 according to the original evidence; See the separate complete-table record for edition 2018.
X6Cr17 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
DIN EN 10263-5-2002
Table / clause
Table 2 and notes a–e; Table 3 is cited only for deviations
PDF page references
1、8、9
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default heat-analysis values in historical Table 2
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: C≤0.04% agreed at enquiry or ordering to improve cold formability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e. / Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges. / Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use. / This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options. / For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti. / The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Composition conditions
Source actually used: DIN EN10263-5:2002-02, the German-language adoption of EN10263-5:2001; PDF8, Table 2 and notes a–e.
Default heat analysis in wt%.; Apply product-analysis tolerances in Table 3 separately; do not add them to the default heat-analysis range.
Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; Residual elements must not impair the properties or intended use.
The older table does not use the 2017 edition’s separate sulfur conditions; do not copy machining/welding/polishing options from the newer edition..
For Ti-stabilized grades, check 5×C≤Ti≤0.70% against measured C.; Does not apply to grades for which Ti is not specified.
Standard range for cold-heading and cold-extrusion; actual supply, dimensions, delivery condition, and performance still require confirmation..
Original condition-branch records
Default heat-analysis values in historical Table 2
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b: C≤0.04% agreed at enquiry or ordering to improve cold formability
Element
Composition requirement
C
≤ 0.04 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
A condition branch must be selected
Yes
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotes
X6Cr17 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
DIN EN 10263-5-2002
Table / clause
Table 2 and notes a–e; Table 3 is cited only for deviations
PDF page references
1、8、9
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default heat-analysis values in historical Table 2
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: C≤0.04% agreed at enquiry or ordering to improve cold formability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e. / Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges. / Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use. / This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options. / For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti. / The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Composition conditions
Source actually used: DIN EN10263-5:2002-02, the German-language adoption of EN10263-5:2001; PDF8, Table 2 and notes a–e.
Default heat analysis in wt%.; Apply product-analysis tolerances in Table 3 separately; do not add them to the default heat-analysis range.
Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; Residual elements must not impair the properties or intended use.
The older table does not use the 2017 edition’s separate sulfur conditions; do not copy machining/welding/polishing options from the newer edition..
For Ti-stabilized grades, check 5×C≤Ti≤0.70% against measured C.; Does not apply to grades for which Ti is not specified.
Standard range for cold-heading and cold-extrusion; actual supply, dimensions, delivery condition, and performance still require confirmation..
Original condition-branch records
Default heat-analysis values in historical Table 2
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b: C≤0.04% agreed at enquiry or ordering to improve cold formability
Element
Composition requirement
C
≤ 0.04 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
A condition branch must be selected
Yes
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotes
X6Cr17 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
EN 10088-1-2005
Table / clause
Table 2 and notes a–c; all 21 ferritic stainless steel grades
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Ordinary sulfur maximum in Table 2; the long-product condition in note b has not been selected
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the corresponding semi-finished products
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b recommends and permits S .015–.030 to improve machinability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b recommends and permits S .008–.030 to improve weldability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b recommends S≤.015 for polishability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
EN10088-1:2005, Table 2, cast/heat-analysis mass fractions wt%; complete Table 2 in the official SIST adoption preview PDF8; The preview is not the complete standard. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; A blank is not zero; no residual maximum is inserted without a source. ; Note b applies only to grades marked b; S must be checked separately for the selected product and property conditions and is not extended to the entire table. ; The coupled minimum for Ti/Nb/Zr and C/N is retained separately; no N maximum is provided in the table, and this is not entered as zero; The corresponding coupled condition cannot be confirmed without measured N. ; This part is a stainless steel designation list; specific delivery and mechanical-property requirements must follow the corresponding product standard; Cold-heading suitability, supply or equivalence between national editions is not established.
Combined limits
Elements requiring measured values from the same heat
Original condition-branch records
Ordinary sulfur maximum in Table 2; the long-product condition in note b has not been selected
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the corresponding semi-finished products
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b recommends and permits S .015–.030 to improve machinability
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.015 ～ 0.03
Cr
16.0 ～ 18.0
Note b recommends and permits S .008–.030 to improve weldability
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.008 ～ 0.03
Cr
16.0 ～ 18.0
Note b recommends S≤.015 for polishability
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
A condition branch must be selected
Yes
Verification notes
Visual verification of all 21 rows and footnotes in original Table 2; stabilization is retained only for explicitly specified routes.
X6Cr17 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
EN 10088-1-2005
Table / clause
Table 2 and notes a–c; all 21 ferritic stainless steel grades
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Ordinary sulfur maximum in Table 2; the long-product condition in note b has not been selected
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the corresponding semi-finished products
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b recommends and permits S .015–.030 to improve machinability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b recommends and permits S .008–.030 to improve weldability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b recommends S≤.015 for polishability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
EN10088-1:2005, Table 2, cast/heat-analysis mass fractions wt%; complete Table 2 in the official SIST adoption preview PDF8; The preview is not the complete standard. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; A blank is not zero; no residual maximum is inserted without a source. ; Note b applies only to grades marked b; S must be checked separately for the selected product and property conditions and is not extended to the entire table. ; The coupled minimum for Ti/Nb/Zr and C/N is retained separately; no N maximum is provided in the table, and this is not entered as zero; The corresponding coupled condition cannot be confirmed without measured N. ; This part is a stainless steel designation list; specific delivery and mechanical-property requirements must follow the corresponding product standard; Cold-heading suitability, supply or equivalence between national editions is not established.
Combined limits
Elements requiring measured values from the same heat
Original condition-branch records
Ordinary sulfur maximum in Table 2; the long-product condition in note b has not been selected
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the corresponding semi-finished products
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b recommends and permits S .015–.030 to improve machinability
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.015 ～ 0.03
Cr
16.0 ～ 18.0
Note b recommends and permits S .008–.030 to improve weldability
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.008 ～ 0.03
Cr
16.0 ～ 18.0
Note b recommends S≤.015 for polishability
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
A condition branch must be selected
Yes
Verification notes
Visual verification of all 21 rows and footnotes in original Table 2; stabilization is retained only for explicitly specified routes.
X6Cr17 · NF EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Composition basis in the adopted standard verified
Standard edition
EN 10088-1-2005
Table / clause
Table 2 and notes a–c; all 21 ferritic stainless steel grades
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Ordinary sulfur maximum in Table 2; the long-product condition in note b has not been selected
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the corresponding semi-finished products
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b recommends and permits S .015–.030 to improve machinability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b recommends and permits S .008–.030 to improve weldability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b recommends S≤.015 for polishability
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
NF EN 10088-1:2005 adopts EN 10088-1:2005 (EN 10088-1-2005); See the data basis for the actual composition source file and table number. EN10088-1:2005, Table 2, cast/heat-analysis mass fractions wt%; complete Table 2 in the official SIST adoption preview PDF8; The preview is not the complete standard. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; A blank is not zero; no residual maximum is inserted without a source. ; Note b applies only to grades marked b; S must be checked separately for the selected product and property conditions and is not extended to the entire table. ; The coupled minimum for Ti/Nb/Zr and C/N is retained separately; no N maximum is provided in the table, and this is not entered as zero; The corresponding coupled condition cannot be confirmed without measured N. ; This part is a stainless steel designation list; specific delivery and mechanical-property requirements must follow the corresponding product standard; Cold-heading suitability, supply or equivalence between national editions is not established.
Combined limits
Elements requiring measured values from the same heat
Original condition-branch records
Ordinary sulfur maximum in Table 2; the long-product condition in note b has not been selected
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the corresponding semi-finished products
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Note b recommends and permits S .015–.030 to improve machinability
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.015 ～ 0.03
Cr
16.0 ～ 18.0
Note b recommends and permits S .008–.030 to improve weldability
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.008 ～ 0.03
Cr
16.0 ～ 18.0
Note b recommends S≤.015 for polishability
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
A condition branch must be selected
Yes
Verification notes
The formal adoption relationship and corresponding EN composition original have been checked; the complete national adoption text has not been verified page by page.
X6Cr17 · ISO 15510-2014
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material category
Stainless steel
Subcategory
Stainless steel
Material form
Reference record
Original record status
Original standard verified
Standard edition
ISO 15510-2014
Table / clause
The current grade row in Table1; Note a and corresponding footnotes (original text on the publishing platform)
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 1 base range: C≤0.08%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note i: C≤0.12% may be agreed for specific applications such as weldability or high-strength wire; Not applied without agreement
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
ISO 15510:2014, Table 1 gives heat analysis, mass fractions wt%; Under note a, values without a stated range or minimum are maxima; a dash is not treated as zero. Composition rows follow an excerpt of the official PDF edition; relevant footnotes follow the original Table 1 in the Sample text section of the standards publishing platform; Verification of the complete standard text or mechanical properties is not claimed. The standard covers material for wrought products, including ingots and semi-finished products; Similar composition does not establish direct substitution; cold-heading suitability and supply condition require separate confirmation. The S 0.015–0.030% machinability recommendations, 0.008–0.020% weldability recommendation and S≤0.015% polishability recommendation in note b concern specific properties and do not directly replace this row’s sulfur limits.
Original condition-branch records
Table 1 base range: C≤0.08%
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Note i: C≤0.12% may be agreed for specific applications such as weldability or high-strength wire; Not applied without agreement
Element
Composition requirement
C
≤ 0.12 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
A condition branch must be selected
Yes
Verification notes
The row for this grade in Table 1 has been checked against the official PDF; Relevant original footnotes are retained in the supporting verification record; Full standard text and mechanical properties to be verified separately
X6Cr17 · DIN EN 10263-5-2018
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
Material form
Reference record
Original record status
Original standard verified
Standard edition
DIN EN 10263-5:2018-02
Table / clause
Tabelle 3 and footnote a–e; Tabelle 4 product-analysis tolerances require separate verification
PDF page references
1、10、11
Unit
Mass fraction (wt%)
Analysis type
Heat analysis
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default composition in Table 3
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Machinability condition S 0.015–0.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Weldability condition S 0.008–0.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Polishability recommendation S≤0.015%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default composition in Table 3; Agreed cold-forming C≤0.04%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Machinability condition S 0.015–0.030%; Agreed cold-forming C≤0.04%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Weldability condition S 0.008–0.030%; Agreed cold-forming C≤0.04%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Applicability and limitations
DIN EN 10263-5:2018-02 is the German-language edition of EN 10263-5:2017; This record was verified against heat analysis and footnotes in Table 3 of the official German edition. ; Heat-analysis mass fractions wt%; Product-analysis tolerances follow Table 4 separately. ; The sulfur conditions for machining, welding and polishing in Table 3, note b are retained separately; different requirements are not imposed simultaneously. ; Ti-stabilized grades require 5×C≤Ti≤0.70%, checked jointly with measured C/Ti. ; This standard covers stainless steel for cold heading and cold extrusion; delivery condition, dimensions, surface and mechanical properties still require independent confirmation. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; unspecified contents are not treated as zero. ; Note c: C≤0.04% may be agreed at enquiry or ordering to improve cold formability; Default tabulated limit ≤0.08%.
Original condition-branch records
Default composition in Table 3
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Machinability condition S 0.015–0.030%
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.015 ～ 0.03
Cr
16.0 ～ 18.0
Weldability condition S 0.008–0.030%
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.008 ～ 0.03
Cr
16.0 ～ 18.0
Polishability recommendation S≤0.015%
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Cr
16.0 ～ 18.0
Default composition in Table 3; Agreed cold-forming C≤0.04%
Element
Composition requirement
C
≤ 0.04 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.03 (lower limit not stated)
Cr
16.0 ～ 18.0
Machinability condition S 0.015–0.030%; Agreed cold-forming C≤0.04%
Element
Composition requirement
C
≤ 0.04 (lower limit not stated)
Si
≤ 1.0 (lower limit not stated)
Mn
≤ 1.0 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
0.015 ～ 0.03
Cr
16.0 ～ 18.0
Weldability condition S 0.008–0.030%; Agreed cold-forming C≤0.04%
DIN EN 10263-5:2018-02 official German edition, Table 3, row 17 and notes a–e checked; adopts EN 10263-5:2017.
X6Cr17 · EN 10263
Original-source verification is incomplete; this is not a formal standard reference
Material category
Stainless steel
Subcategory
Stainless steel
Material form
Drawn wire
Verification status
Published on the website; original-source verification pending
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
Element
Composition requirement
C
≤ 0.08 (lower limit not stated)
Cr
16 ～ 18
Mn
≤ 1 (lower limit not stated)
P
≤ 0.04 (lower limit not stated)
S
≤ 0.015 (lower limit not stated)
Si
≤ 1 (lower limit not stated)
Applicability and limitations
Give priority to the published technical page on the Creation Group website. Use local reference ranges only as supplementary composition cross-checks; the applicable standard for that product page, the technical agreement and actual verification take precedence.
