X3CRNIMO17-13-3
11 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for X3CRNIMO17-13-3 →Material demand assessment
Looking for X3CRNIMO17-13-3 material?
Not listed in our catalog? You are welcome to submit your requirements. We assess whether our equipment, production lines and process capabilities suit your grade, product form, dimensions, processing and delivery requirements, then discuss possible processing, trials or supply arrangements.
Feasibility and supply terms are confirmed after technical review. The standard information on this page is not a supply or performance commitment.
Keep your entries and try again later, or contact website@chqwire.net. If you have already received confirmation, do not submit again.
X3CrNiMo17-13-3 · ISO 4954
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Stainless steel
- Subcategory
- Stainless steel
- Material form
- Cold-heading wire
- Original record status
- Source edition identified; composition verification pending
- Standard edition
- ISO 4954:2018
- Table / clause
- Table D.2
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Ni | 10.5 ～ 13 |
| Mo | 2.5 ～ 3 |
| N | ≤ 0.1 (lower limit not stated) |
| Cu | ≤ 1 (lower limit not stated) |
Applicability and limitations
Composition based on ISO 4954:2018; the product edition is unspecified, so confirm the edition applicable to the contract.
Composition conditions
- ISO 4954:2018, Table D.2 gives heat analysis; A single value is a maximum; a dash is not zero.
- Product-analysis tolerances are listed separately under Table 2/3 of the standard and do not directly widen the heat-analysis composition ranges.
- Unlisted elements must not be intentionally added without purchaser consent, except for additions needed to finish the heat.
Verification notes
Composition based on ISO 4954:2018; the product edition is unspecified, so confirm the edition applicable to the contract.View associated products →X3CrNiMo17-13-3 · ISO 4954-2018
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Stainless steel
- Subcategory
- Stainless steel
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- ISO 4954:2018
- Table / clause
- Table D.2
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Ni | 10.5 ～ 13 |
| Mo | 2.5 ～ 3 |
| N | ≤ 0.1 (lower limit not stated) |
| Cu | ≤ 1 (lower limit not stated) |
Applicability and limitations
ISO 4954:2018 Table D.2 gives cast analysis; single values are maxima and dashes are not zero.
Product-analysis deviations are listed separately under Tables 2/3, not used directly to relax cast-composition limits.
Elements not listed must not be intentionally added without the purchaser's consent, except for finishing the heat.
Verification notes
The original standard, Table D.2 and footnotes have been checkedX3CrNiMo17-13-3 · EN 10263-5-2017
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10263-5-2017
- Table / clause
- Table 3 and footnotes a–e
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default composition in Table 3
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Machinability condition S 0.015–0.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Weldability condition S 0.008–0.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Polishability recommendation S≤0.015%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
Applicability and limitations
Heat-analysis mass fractions wt%; Product-analysis tolerances follow Table 4 separately. ; The sulfur conditions for machining, welding and polishing in Table 3, note b are retained separately; different requirements are not imposed simultaneously. ; Ti-stabilized grades require 5×C≤Ti≤0.70%, checked jointly with measured C/Ti. ; This standard covers stainless steel for cold heading and cold extrusion; delivery condition, dimensions, surface and mechanical properties still require independent confirmation. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; unspecified contents are not treated as zero.
Original condition-branch records
Default composition in Table 3
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
Machinability condition S 0.015–0.030%
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
Weldability condition S 0.008–0.030%
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
Polishability recommendation S≤0.015%
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
The original English Table 3 and footnotes have been checkedX3CrNiMo17-13-3 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- DIN EN 10263-5-2002
- Table / clause
- Table 2 and notes a–e; Table 3 is cited only for deviations
- PDF page references
- 1、8、9
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.11 (lower limit not stated) |
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e.
Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges.
Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use.
This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options.
For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti.
The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Original condition-branch records
Default heat-analysis values in historical Table 2
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.11 (lower limit not stated) |
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotesX3CrNiMo17-13-3 · EN 10263-5-2001
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10263-5-2001
- Table / clause
- Table 2 and notes a–e; Table 3 is cited only for deviations
- PDF page references
- 1、8、9
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.11 (lower limit not stated) |
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e.
Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges.
Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use.
This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options.
For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti.
The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Original condition-branch records
Default heat-analysis values in historical Table 2
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.11 (lower limit not stated) |
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotesX3CrNiMo17-13-3 · DIN EN 10263-5-2002
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- DIN EN 10263-5-2002
- Table / clause
- Table 2 and notes a–e; Table 3 is cited only for deviations
- PDF page references
- 1、8、9
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.11 (lower limit not stated) |
Applicability and limitations
Actual source: DIN EN 10263-5:2002-02; German adoption of EN 10263-5:2001, PDF p. 8 Table 2 and Notes a–e.
Default is ladle analysis, mass fraction wt%; product-analysis deviations are separately governed by Table 3 and are not added to default ladle ranges.
Unlisted elements must not be intentionally added without purchaser approval (except as necessary during steelmaking); residual elements must not impair performance or use.
This older edition does not use the 2017 edition’s conditional sulfur provisions; do not copy newer machining/welding/polishing options.
For Ti-stabilized grades, verify 5×C≤Ti≤0.70% using measured C; do not apply this condition to grades without Ti.
The standard covers cold heading/cold extrusion; actual supply, dimensions, delivery condition and properties still require confirmation.
Original condition-branch records
Default heat-analysis values in historical Table 2
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.11 (lower limit not stated) |
Verification notes
Visual check of the previous-edition cover, all 19 grades in Table 2, and footnotesX3CrNiMo17-13-3 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 4 and continuation; notes a–e; all 50 austenitic corrosion-resistant steel grades
- PDF page references
- 1、3、11、12
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default sulfur requirement; default Ni; the cold-heading Cu exception is not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulphur requirement; default Ni; note c: Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Applicability and limitations
EN 10088-1:2005 Table 4 and continuation: ladle analysis (wt%); the official SIST adoption preview PDF, pages 11/12, covers all 50 grades and notes. Note a: unlisted elements are not intentionally added without purchaser consent, except as needed to complete steelmaking; a blank is not zero. Note b: for grades marked b only, S is selected separately for long products and by property requirement. Note d: the increased Ni maximum for special reasons applies only to listed grades, not all grades. Note c: Cu up to 1.0% for cold heading/extrusion; this condition path is provided here only for grades with blank Cu in the original table. Existing Cu alloy ranges retain their original values; the exception has not automatically rewritten them. The linked Ti≥5C/Nb≥10C and Ti≥8(C+N) conditions are retained; an unlisted N maximum is not zero. Note e: the source warns of skin-contact regulatory issues for high-sulfur free-machining steel; this is retained as a historical warning only and is not a claim of current compliance based on the 2005 text. Listed chemistry and the cold-heading Cu exception alone do not establish overall cold-heading performance or company supply; mechanical and product standards must be checked separately, and national adoption does not mean automatic equivalence.
Original condition-branch records
Default sulfur requirement; default Ni; the cold-heading Cu exception is not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Default sulphur requirement; default Ni; note c: Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
Official source Table 4, all 50 rows and footnotes visually checked; conditional route for Cu cells left blank in the original.X3CrNiMo17-13-3 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 4 and continuation; notes a–e; all 50 austenitic corrosion-resistant steel grades
- PDF page references
- 1、3、11、12
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default sulfur requirement; default Ni; the cold-heading Cu exception is not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulphur requirement; default Ni; note c: Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Applicability and limitations
EN 10088-1:2005 Table 4 and continuation: ladle analysis (wt%); the official SIST adoption preview PDF, pages 11/12, covers all 50 grades and notes. Note a: unlisted elements are not intentionally added without purchaser consent, except as needed to complete steelmaking; a blank is not zero. Note b: for grades marked b only, S is selected separately for long products and by property requirement. Note d: the increased Ni maximum for special reasons applies only to listed grades, not all grades. Note c: Cu up to 1.0% for cold heading/extrusion; this condition path is provided here only for grades with blank Cu in the original table. Existing Cu alloy ranges retain their original values; the exception has not automatically rewritten them. The linked Ti≥5C/Nb≥10C and Ti≥8(C+N) conditions are retained; an unlisted N maximum is not zero. Note e: the source warns of skin-contact regulatory issues for high-sulfur free-machining steel; this is retained as a historical warning only and is not a claim of current compliance based on the 2005 text. Listed chemistry and the cold-heading Cu exception alone do not establish overall cold-heading performance or company supply; mechanical and product standards must be checked separately, and national adoption does not mean automatic equivalence.
Original condition-branch records
Default sulfur requirement; default Ni; the cold-heading Cu exception is not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Default sulphur requirement; default Ni; note c: Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
Official source Table 4, all 50 rows and footnotes visually checked; conditional route for Cu cells left blank in the original.X3CrNiMo17-13-3 · NF EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Composition basis in the adopted standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 4 and continuation; notes a–e; all 50 austenitic corrosion-resistant steel grades
- PDF page references
- 1、3、11、12
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default sulfur requirement; default Ni; the cold-heading Cu exception is not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulphur requirement; default Ni; note c: Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Applicability and limitations
NF EN 10088-1:2005 adopts EN 10088-1:2005 (EN 10088-1-2005); See the data basis for the actual composition source file and table number. EN10088-1:2005 Table 4 and its continuation; heat analysis wt%; all 50 grades and footnotes on PDF pages 11/12 of the official SIST adoption preview.. ; Note a: Elements not listed shall not be intentionally added without the consent of the purchaser (except additions needed to finish steelmaking).; Blanks are not entered as zero. ; Note b: For grades marked b, S shall be selected separately according to long products and properties.; The increased Ni upper limit based on special reasons in Note d applies only to the listed steel grades and cannot be generalized to all grades.. ; Note c: For cold-heading/cold-extrusion applications, Cu max 1.0%.; This conditional path is provided only for grades where Cu was blank in the original table; existing Cu alloying ranges shall retain their original values, and their Cu exceptions have not been automatically rewritten.. ; The linkages Ti≥5C/Nb≥10C and Ti≥8(C+N) are retained.; If no N upper limit is listed, do not fill as zero.. ; Note e retains the original historical caution about skin-contact regulations for high-sulfur free-cutting steel; the 2005 text is not used to claim present-day compliance.. ; The listed compositions and the cold-heading Cu exception do not independently prove the overall cold-heading properties of the material or company supply.; Mechanical properties and product standards require separate verification; national adoption does not automatically establish equivalence..
Original condition-branch records
Default sulfur requirement; default Ni; the cold-heading Cu exception is not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Default sulphur requirement; default Ni; note c: Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Default sulfur requirement; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, S for long products/wire etc.: ≤0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, S for long products/wire etc.: ≤0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S≤.030 applies to long products, wire and the other stated forms; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, recommended S for machining: 0.015–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, recommended S for machining: 0.015–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S .015–.030 is recommended for machining; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, recommended S for welding: 0.008–0.030%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, recommended S for welding: 0.008–0.030%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S .008–.030 is recommended for welding; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b, recommended S for polishing: ≤0.015%Default Ni; cold-heading Cu exception not selected, so the original-table Cu requirement applies.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
Note b, recommended S for polishing: ≤0.015%Default Ni; note c allows Cu≤1.0% for cold heading/cold extrusion.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; The cold-heading Cu exception has not been selected; the original table requires Cu
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
Note b: S≤.015 is recommended for polishing; Note d: Ni increases 1% under specified low-permeability, processing or other special conditions; Note c: Cu≤1.0% applies when used for cold heading or cold extrusion
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| N | ≤ 0.11 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 14.0 |
| Cu | ≤ 1.0 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
The formal adoption relationship and corresponding EN composition original have been checked; the complete national adoption text has not been verified page by page.X3CrNiMo17-13-3 · DIN EN 10263-5-2018
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- DIN EN 10263-5:2018-02
- Table / clause
- Tabelle 3 and footnote a–e; Tabelle 4 product-analysis tolerances require separate verification
- PDF page references
- 1、10、11
- Unit
- Mass fraction (wt%)
- Analysis type
- Heat analysis
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default composition in Table 3
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Machinability condition S 0.015–0.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Weldability condition S 0.008–0.030%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Polishability recommendation S≤0.015%
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
Applicability and limitations
DIN EN 10263-5:2018-02 is the German-language edition of EN 10263-5:2017; This record was verified against heat analysis and footnotes in Table 3 of the official German edition. ; Heat-analysis mass fractions wt%; Product-analysis tolerances follow Table 4 separately. ; The sulfur conditions for machining, welding and polishing in Table 3, note b are retained separately; different requirements are not imposed simultaneously. ; Ti-stabilized grades require 5×C≤Ti≤0.70%, checked jointly with measured C/Ti. ; This standard covers stainless steel for cold heading and cold extrusion; delivery condition, dimensions, surface and mechanical properties still require independent confirmation. ; Unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish steelmaking; unspecified contents are not treated as zero.
Original condition-branch records
Default composition in Table 3
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
Machinability condition S 0.015–0.030%
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
Weldability condition S 0.008–0.030%
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
Polishability recommendation S≤0.015%
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 2.0 (lower limit not stated) |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mo | 2.5 ～ 3.0 |
| Ni | 10.5 ～ 13.0 |
| N | ≤ 0.1 (lower limit not stated) |
A condition branch must be selected
YesVerification notes
DIN EN 10263-5:2018-02 official German edition, Table 3, row 12 and notes a–e checked; adopts EN 10263-5:2017.X3CrNiMo17-13-3 · EN 10263
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Stainless steel
- Material form
- Drawn wire
- Verification status
- Published on the website; original-source verification pending
Carbon-equivalent reference
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.05 (lower limit not stated) |
| Cr | 16.5 ～ 18.5 |
| Mn | ≤ 2 (lower limit not stated) |
| Mo | 2.5 ～ 3 |
| N | ≤ 0.11 (lower limit not stated) |
| Ni | 10.5 ～ 13 |
| P | ≤ 0.045 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
Give priority to the published technical page on the Creation Group website. Use local reference ranges only as supplementary composition cross-checks; the applicable standard for that product page, the technical agreement and actual verification take precedence.