YGW13

1 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.

Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.

Open condition selection, comparison and carbon-equivalent tools for YGW13 →

Material demand assessment

Looking for YGW13 material?

Not listed in our catalog? You are welcome to submit your requirements. We assess whether our equipment, production lines and process capabilities suit your grade, product form, dimensions, processing and delivery requirements, then discuss possible processing, trials or supply arrangements.

Feasibility and supply terms are confirmed after technical review. The standard information on this page is not a supply or performance commitment.

Explore products and processing capabilities

Discuss your requirements with our technical team

YGW13 · CHINA STEEL CORPORATION · Bars and Wire Rods Product Catalogue 2014-C1 / 7.1.14 JIS Z3312-2009

Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results

Material category: Carbon steel
Subcategory: Carbon steel
Material form: Bars and wire rod
Original record status: Manufacturer source verified
Document edition: CAT.NO.3-BD-01-2014-C1 (stated on the back cover)
Document title: Bars and Wire Rods Product Catalogue
Table / clause: 7.1.14 JIS Z3312-2009
PDF page references: 21
Unit: Mass fraction (%)
Analysis type: The original catalogue does not explicitly identify the analysis type for this table
Manufacturer: CHINA STEEL CORPORATION

Carbon-equivalent reference

Estimate from manufacturer-published ranges, not a standard guarantee or measured heat result; formula applicability requires review against the application and process.

IIW / CEV：0.2450–0.5000Known-element contribution; incomplete value; missing Cr, Mo, V, Ni; coupled-element constraints require separate checks; the entire envelope is not guaranteed to be realizable CEV = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15; an engineering estimate of welding cold-cracking susceptibility for carbon and low-alloy steels.

Pcm（Ito–Bessyo）：0.1058–0.3067Known-element contribution; incomplete value; missing Cr, Ni, Mo, V, B; coupled-element constraints require separate checks; the entire envelope is not guaranteed to be realizable Pcm = C + Si/30 + (Mn + Cu + Cr)/20 + Ni/60 + Mo/15 + V/10 + 5B; mainly used for low-carbon low-alloy steels, particularly modern low-carbon pipeline steels; more relevant when C is approximately no higher than 0.11%.

CET：0.1550–0.3650Known-element contribution; incomplete value; missing Mo, Cr, Ni; coupled-element constraints require separate checks; the entire envelope is not guaranteed to be realizable CET = C + (Mn + Mo)/10 + (Cr + Cu)/20 + Ni/40; used in welding preheat assessment for ferritic steels, subject to the applicability conditions of EN 1011-2.

Composition

Element	Composition requirement
C	0.02 ～ 0.15
Si	0.55 ～ 1.1
Mn	1.35 ～ 1.9
P	≤ 0.03 (lower limit not stated)
S	≤ 0.03 (lower limit not stated)
Cu	≤ 0.5 (lower limit not stated)
Al	0.1 ～ 0.5

Applicability and limitations

China Steel bar and wire-rod catalogue CAT.NO.3-BD-01-2014-C1, PDF page 21

printed page 19, 7.1.14 JIS Z3312-2009. The original catalogue does not explicitly identify the analysis type for this table. Historical manufacturer range data, not guaranteed standard limits or heat-specific measurements; this does not establish supply by Creation Group. Condition: Ti+Zr is a total only and is not split into independent limits; Lower and upper bounds are applied as linear constraints.

Composition conditions

Historical manufacturer 2014-C1 catalogue, bars/wire rod; Where the referenced standard edition is not identified, a year is not borrowed from another catalogue; a catalogue is not upgraded to the official standard text.
A dash or blank must not be treated as zero. Composition data do not establish completeness or applicability of a formula; mechanical properties and supply require separate verification.
Ti+Zr is a total only and is not split into independent limits; Lower and upper bounds are applied as linear constraints.

Combined limits

Combined-element limits

Element coefficient
Ti
1
Zr
1
Lower limit
0.02
Upper limit
0.03

Elements requiring measured values from the same heat

Verification notes

Merged cells in all 28 catalogue tables were reconstructed geometrically, with no missing cells. Original images, continuation pages and notes are recorded; disputed conditions are withheld.