X5CRNICUNB16-4
7 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for X5CRNICUNB16-4 →Material demand assessment
Looking for X5CRNICUNB16-4 material?
Not listed in our catalog? You are welcome to submit your requirements. We assess whether our equipment, production lines and process capabilities suit your grade, product form, dimensions, processing and delivery requirements, then discuss possible processing, trials or supply arrangements.
Feasibility and supply terms are confirmed after technical review. The standard information on this page is not a supply or performance commitment.
Keep your entries and try again later, or contact website@chqwire.net. If you have already received confirmation, do not submit again.
X5CrNiCuNb16-4 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Stainless steel
- Subcategory
- Precipitation-hardening stainless steel
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 3 and continuation, notes a–d; all 30 martensitic and precipitation-hardening corrosion-resistant steel grades
- PDF page references
- 1、3、9、10
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
Note b recommends and permits S .015–.030 for machinability
Note b recommends and permits S .008–.030 for weldability
Note b recommends S≤.015 for polishability
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Applicability and limitations
EN10088-1:2005, Table 3 including its continuation, heat analysis wt%; official English SIST adoption preview PDF9/10. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; blanks are not filled with zero or a general residual maximum. ; Note b distinguishes sulfur conditions for long products, machining, welding and polishing only for grades marked b; it is not extended to all grades. ; Note c: a narrower C range may be agreed at enquiry and ordering; Without a contract, the original table range is not replaced. ; Note d: only for X7CrNiAl17-7 to improve cold-deformation performance, the Ni maximum is 8.3%; select separately from default 7.8. ; A designation-list standard does not independently establish cold-heading suitability, mechanical-property delivery requirements or product supply; Adopted editions such as NF/DIN are not automatically verified by this European main text.
Combined limits
- Combined-element limits
- Element coefficient
- Nb
- 1
- C
- -5
- Lower limit
- 0
- Requirement
- Nb≥5C
Original condition-branch records
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b recommends and permits S .015–.030 for machinability
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b recommends and permits S .008–.030 for weldability
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b recommends S≤.015 for polishability
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
A condition branch must be selected
YesVerification notes
All 30 rows of Table 3 and footnotes visually checked.X5CrNiCuNb16-4 · NF EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Stainless steel
- Subcategory
- Precipitation-hardening stainless steel
- Material form
- Reference record
- Original record status
- Composition basis in the adopted standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 3 and continuation, notes a–d; all 30 martensitic and precipitation-hardening corrosion-resistant steel grades
- PDF page references
- 1、3、9、10
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
Note b recommends and permits S .015–.030 for machinability
Note b recommends and permits S .008–.030 for weldability
Note b recommends S≤.015 for polishability
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Applicability and limitations
NF EN 10088-1:2005 adopts EN 10088-1:2005 (EN 10088-1-2005); See the data basis for the actual composition source file and table number. EN10088-1:2005, Table 3 including its continuation, heat analysis wt%; official English SIST adoption preview PDF9/10. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; blanks are not filled with zero or a general residual maximum. ; Note b distinguishes sulfur conditions for long products, machining, welding and polishing only for grades marked b; it is not extended to all grades. ; Note c: a narrower C range may be agreed at enquiry and ordering; Without a contract, the original table range is not replaced. ; Note d: only for X7CrNiAl17-7 to improve cold-deformation performance, the Ni maximum is 8.3%; select separately from default 7.8. ; A designation-list standard does not independently establish cold-heading suitability, mechanical-property delivery requirements or product supply; Adopted editions such as NF/DIN are not automatically verified by this European main text.
Combined limits
- Combined-element limits
- Element coefficient
- Nb
- 1
- C
- -5
- Lower limit
- 0
- Requirement
- Nb≥5C
Original condition-branch records
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b recommends and permits S .015–.030 for machinability
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b recommends and permits S .008–.030 for weldability
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b recommends S≤.015 for polishability
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
A condition branch must be selected
YesVerification notes
The formal adoption relationship and corresponding EN composition original have been checked; the complete national adoption text has not been verified page by page.X5CrNiCuNb16-4 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 3 and continuation, notes a–d; all 30 martensitic and precipitation-hardening corrosion-resistant steel grades
- PDF page references
- 1、3、9、10
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
Note b recommends and permits S .015–.030 for machinability
Note b recommends and permits S .008–.030 for weldability
Note b recommends S≤.015 for polishability
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Applicability and limitations
EN10088-1:2005, Table 3 including its continuation, heat analysis wt%; official English SIST adoption preview PDF9/10. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; blanks are not filled with zero or a general residual maximum. ; Note b distinguishes sulfur conditions for long products, machining, welding and polishing only for grades marked b; it is not extended to all grades. ; Note c: a narrower C range may be agreed at enquiry and ordering; Without a contract, the original table range is not replaced. ; Note d: only for X7CrNiAl17-7 to improve cold-deformation performance, the Ni maximum is 8.3%; select separately from default 7.8. ; A designation-list standard does not independently establish cold-heading suitability, mechanical-property delivery requirements or product supply; Adopted editions such as NF/DIN are not automatically verified by this European main text.
Combined limits
- Combined-element limits
- Element coefficient
- Nb
- 1
- C
- -5
- Lower limit
- 0
- Requirement
- Nb≥5C
Original condition-branch records
Table 3, ordinary S≤.015; the long-product condition in note b has not been selected
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b: S≤.030 applies to bars, wire rod, wire, sections, bright products and the relevant semi-finished products
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b recommends and permits S .015–.030 for machinability
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.015 ～ 0.03 |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b recommends and permits S .008–.030 for weldability
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | 0.008 ～ 0.03 |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
Note b recommends S≤.015 for polishability
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 15.0 ～ 17.0 |
| Cu | 3.0 ～ 5.0 |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | ≤ 0.45 (lower limit not stated) |
| Ni | 3.0 ～ 5.0 |
A condition branch must be selected
YesVerification notes
All 30 rows of Table 3 and footnotes visually checked.X5CrNiCuNb16-4 · NF EN 10088-2-2005
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Precipitation-hardening stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Cr | 15 ～ 17 |
| Cu | 3 ～ 5 |
| Mn | ≤ 1.5 (lower limit not stated) |
| Mo | ≤ 0.6 (lower limit not stated) |
| Ni | 3 ～ 5 |
| P | ≤ 0.04 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X5CrNiCuNb16-4 · ISO 15510-2014
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Precipitation-hardening stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Cr | 15 ～ 17 |
| Cu | 3 ～ 5 |
| Mn | ≤ 1.5 (lower limit not stated) |
| Mo | ≤ 0.6 (lower limit not stated) |
| Nb | 0.15 ～ 0.45 |
| Ni | 3 ～ 5 |
| P | ≤ 0.04 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X5CrNiCuNb16-4 · ISO 683-18
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Precipitation-hardening stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Cr | 15 ～ 17 |
| Cu | 3 ～ 5 |
| Mn | ≤ 1.5 (lower limit not stated) |
| Mo | ≤ 0.6 (lower limit not stated) |
| Ni | 3 ～ 5 |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X5CrNiCuNb16-4 · ISO TS 15510-2003
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Precipitation-hardening stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.07 (lower limit not stated) |
| Cr | 15 ～ 17 |
| Cu | 3 ～ 5 |
| Mn | ≤ 1.5 (lower limit not stated) |
| Mo | ≤ 0.6 (lower limit not stated) |
| Ni | 3 ～ 5 |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Si | ≤ 0.7 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.