X2CRTI12
11 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for X2CRTI12 →Material demand assessment
Looking for X2CRTI12 material?
Not listed in our catalog? You are welcome to submit your requirements. We assess whether our equipment, production lines and process capabilities suit your grade, product form, dimensions, processing and delivery requirements, then discuss possible processing, trials or supply arrangements.
Feasibility and supply terms are confirmed after technical review. The standard information on this page is not a supply or performance commitment.
Keep your entries and try again later, or contact website@chqwire.net. If you have already received confirmation, do not submit again.
X2CrTi12 · NF EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Stainless steel
- Subcategory
- Ferritic stainless steel
- Material form
- Reference record
- Original record status
- Composition basis in the adopted standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 2 and notes a–c; all 21 ferritic stainless steel grades
- PDF page references
- 1、3、7、8
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.0 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Ti | ≤ 0.65 (lower limit not stated) |
Applicability and limitations
NF EN 10088-1:2005 adopts EN 10088-1:2005; Composition is taken from the original EN table for the same designation. EN10088-1:2005, Table 2, cast/heat-analysis mass fractions wt%; complete Table 2 in the official SIST adoption preview PDF8; The preview is not the complete standard. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; A blank is not zero; no residual maximum is inserted without a source. ; Note b applies only to grades marked b; S must be checked separately for the selected product and property conditions and is not extended to the entire table. ; The coupled minimum for Ti/Nb/Zr and C/N is retained separately; no N maximum is provided in the table, and this is not entered as zero; The corresponding coupled condition cannot be confirmed without measured N. ; This part is a stainless steel designation list; specific delivery and mechanical-property requirements must follow the corresponding product standard; Cold-heading suitability, supply or equivalence between national editions is not established. ; Ti≥6(C+N)
Combined limits
- Combined-element limits
- Element coefficient
- Ti
- 1
- C
- -6
- N
- -6
- Lower limit
- 0
- Requirement
- Ti≥6(C+N)
- Elements requiring measured values from the same heat
- N
Verification notes
The official adoption relationship and original same-designation EN table have been checked; The complete French main text has not been checked page by pageX2CrTi12 · EN 10088-1-2005
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10088-1-2005
- Table / clause
- Table 2 and notes a–c; all 21 ferritic stainless steel grades
- PDF page references
- 1、3、7、8
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.0 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Ti | ≤ 0.65 (lower limit not stated) |
Applicability and limitations
EN10088-1:2005, Table 2, cast/heat-analysis mass fractions wt%; complete Table 2 in the official SIST adoption preview PDF8; The preview is not the complete standard. ; Note a: unlisted elements must not be intentionally added without purchaser consent, except additions needed to finish the heat; A blank is not zero; no residual maximum is inserted without a source. ; Note b applies only to grades marked b; S must be checked separately for the selected product and property conditions and is not extended to the entire table. ; The coupled minimum for Ti/Nb/Zr and C/N is retained separately; no N maximum is provided in the table, and this is not entered as zero; The corresponding coupled condition cannot be confirmed without measured N. ; This part is a stainless steel designation list; specific delivery and mechanical-property requirements must follow the corresponding product standard; Cold-heading suitability, supply or equivalence between national editions is not established. ; Ti≥6(C+N)
Combined limits
- Combined-element limits
- Element coefficient
- Ti
- 1
- C
- -6
- N
- -6
- Lower limit
- 0
- Requirement
- Ti≥6(C+N)
- Elements requiring measured values from the same heat
- N
Verification notes
Visual verification of all 21 rows and footnotes in original Table 2; stabilization is retained only for explicitly specified routes.X2CrTi12 · DIN EN 10296-2-2006
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Ferritic stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Mn | ≤ 1 (lower limit not stated) |
| N | ≤ 0.03 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X2CrTi12 · EN 10296-2-2005
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Ferritic stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Mn | ≤ 1 (lower limit not stated) |
| N | ≤ 0.03 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X2CrTi12 · EN 10297-2-2005
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Ferritic stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X2CrTi12 · NF EN 10088-2-2005
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Ferritic stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X2CrTi12 · NF EN 10296-2-2005
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Ferritic stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Mn | ≤ 1 (lower limit not stated) |
| N | ≤ 0.03 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X2CrTi12 · ISO 15510-2014
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Ferritic stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Mn | ≤ 1 (lower limit not stated) |
| N | ≤ 0.03 (lower limit not stated) |
| Ni | ≤ 0.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X2CrTi12 · ISO 4955-2005
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Alloy steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X2CrTi12 · ISO 4955-2016
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Alloy steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
X2CrTi12 · ISO TS 15510-2003
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Ferritic stainless steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | ≤ 0.03 (lower limit not stated) |
| Cr | 10.5 ～ 12.5 |
| Mn | ≤ 1 (lower limit not stated) |
| Ni | ≤ 0.5 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.