VDM ALLOY 33
2 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for VDM ALLOY 33 →Material demand assessment
Looking for VDM ALLOY 33 material?
Not listed in our catalog? You are welcome to submit your requirements. We assess whether our equipment, production lines and process capabilities suit your grade, product form, dimensions, processing and delivery requirements, then discuss possible processing, trials or supply arrangements.
Feasibility and supply terms are confirmed after technical review. The standard information on this page is not a supply or performance commitment.
Keep your entries and try again later, or contact website@chqwire.net. If you have already received confirmation, do not submit again.
VDM Alloy 33 · No corresponding standard is provided
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Special alloy steel
- Material form
- Reference record
- Composition basis
- Manufacturer typical composition range
- Verification status
- Reference data; original source not verified
- Document title
- VDM Material Data Sheet No.4142 Revision01 November2020
- Table / clause
- Table 2 — Typical chemical composition (%)
- PDF page references
- 2、3
- Manufacturer
- VDM Metals
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Ni | 30 ～ 33 |
| Cr | 31 ～ 35 |
| Fe | Balance |
| C | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.01 (lower limit not stated) |
| N | 0.35 ～ 0.6 |
| Mn | ≤ 2 (lower limit not stated) |
| Si | ≤ 0.5 (lower limit not stated) |
| Mo | 0.5 ～ 2 |
| Cu | 0.3 ～ 1.2 |
| P | ≤ 0.02 (lower limit not stated) |
Applicability and limitations
Based on VDM Metals official data dated 2020-11, Rev01, Table 2: a manufacturer typical composition range, not verification of a corresponding standard edition. Fe is balance, may contain other unlisted elements. Table 1 of the datasheet identifies the wire form only for VDM FM33 welding wire; it does not establish suitability for cold heading.
Verification notes
Typical composition ranges from official manufacturer information; Not treated as guaranteed standard valuesVDM Alloy 33 · No corresponding standard is provided
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Special alloy steel
- Material form
- Reference record
- Composition basis
- Manufacturer typical composition range
- Verification status
- Reference data; original source not verified
- Document title
- VDM Material Data Sheet No.4142 Revision01 November2020
- Table / clause
- Table 2 — Typical chemical composition (%)
- PDF page references
- 2、3
- Manufacturer
- VDM Metals
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Ni | 30 ～ 33 |
| Cr | 31 ～ 35 |
| Fe | Balance |
| C | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.01 (lower limit not stated) |
| N | 0.35 ～ 0.6 |
| Mn | ≤ 2 (lower limit not stated) |
| Si | ≤ 0.5 (lower limit not stated) |
| Mo | 0.5 ～ 2 |
| Cu | 0.3 ～ 1.2 |
| P | ≤ 0.02 (lower limit not stated) |
Applicability and limitations
Based on VDM Metals official data dated 2020-11, Rev01, Table 2: a manufacturer typical composition range, not verification of a corresponding standard edition. Fe is balance, may contain other unlisted elements. Table 1 of the datasheet identifies the wire form only for VDM FM33 welding wire; it does not establish suitability for cold heading.