SWRH82A
6 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for SWRH82A →Material demand assessment
Looking for SWRH82A material?
Not listed in our catalog? You are welcome to submit your requirements. We assess whether our equipment, production lines and process capabilities suit your grade, product form, dimensions, processing and delivery requirements, then discuss possible processing, trials or supply arrangements.
Feasibility and supply terms are confirmed after technical review. The standard information on this page is not a supply or performance commitment.
Keep your entries and try again later, or contact website@chqwire.net. If you have already received confirmation, do not submit again.
SWRH82A · JIS G 3506-2024
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Carbon steel
- Subcategory
- Carbon steel
- Material form
- High-carbon steel wire rod; see applicable further-processing and delivery-by-agreement conditions
- Original record status
- Original standard verified
- Standard edition
- JIS G 3506:2024
- Table / clause
- Clause 4/Table 1; Clause 6/Table 2 and note; Annex JA.1
- PDF page references
- 1、5、6、7、11
- Unit
- Mass fraction (wt%)
- Analysis type
- Heat analysis
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Default heat-analysis range in Table 2
JA.1: only by purchaser-supplier agreement, both limits of C are narrowed inward by 0.01 percentage points
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | 0.79 ～ 0.86 |
| Si | 0.15 ～ 0.35 |
| Mn | 0.3 ～ 0.6 |
| P | ≤ 0.03 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
Applicability and limitations
Based on the official Japanese original text of Tables 1/2 and Normative Annex JA of JIS G3506:2024; Heat analysis, mass fraction wt%. Applicable to wire rod intended for further processing into hard-drawn steel wire, oil-quenched and tempered steel wire, prestressed concrete steel wire, galvanized steel strand, steel wire rope, etc.; This standard does not include wire rod for piano wire and wire rod for bridge cables. Cannot be automatically regarded as applicable for cold heading or as a supply guarantee by the company. The default chemical ranges in Table 2 are separate from the narrowed C ranges in JA.1 adopted only by agreement between supplier and purchaser: the upper and lower limits of the agreed range are narrowed inward by 0.01 percentage points each, and are not adopted automatically by default. Alloying elements not listed in Table 2 shall not be intentionally added except for the purpose of finishing steelmaking; Unspecified values shall not be filled as zero, nor shall the complete carbon equivalent be calculated based on this. Clause 9 generally does not specify fixed mechanical properties. Verification shall be performed according to JA.3/JA.4 only when a target tensile strength has been agreed upon and the corresponding agreed delivery condition is adopted; The ±100/±120MPa in Table JA.1 are allowable deviations around the agreed target, not the absolute Rm range, nor a substitute for the target value. Clause 7.1 specifies an average total decarburization layer depth ≤0.20mm; JA.2 may be tightened to ≤0.15mm by agreement. Average total decarburization depth is not the maximum depth of a single field of view; whether to adopt the agreed value must be confirmed separately. Austenitic grain size and non-metallic inclusion limits must be specified by the purchaser and confirmed by agreement under 7.2; a rating cannot be assigned automatically from the grade alone. Table 3 standard diameters are 5.5, 6, 6.4, 7, 8, 9, 9.5, 10, 11, 12, 13, 14, 15mm; Table 4: for diameters ≤15mm, the tolerance is ±0.40mm and the out-of-roundness is ≤0.64mm; For >15mm, agreement is required; do not extrapolate. Inspection, sampling, dimensions, surface, and other product standard conditions shall be verified separately; The relationship with the ISO 16120 series is one of modified adoption, which does not equate to automatic interchangeability of grades.
Original condition-branch records
Default heat-analysis range in Table 2
| Element | Composition requirement |
|---|---|
| C | 0.79 ～ 0.86 |
| Si | 0.15 ～ 0.35 |
| Mn | 0.3 ～ 0.6 |
| P | ≤ 0.03 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
JA.1: only by purchaser-supplier agreement, both limits of C are narrowed inward by 0.01 percentage points
| Element | Composition requirement |
|---|---|
| C | 0.8 ～ 0.85 |
| Si | 0.15 ～ 0.35 |
| Mn | 0.3 ～ 0.6 |
| P | ≤ 0.03 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
- Subject to agreement
- Yes
A condition branch must be selected
YesVerification notes
JIS G3506:2024, Table 2 and the agreed JA condition have been checked; Select the default or agreed carbon range.SWRH82A · JIS G 3506-2004
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Carbon steel
- Material form
- High-carbon steel wire rod
- Original record status
- Original standard verified
- Standard edition
- JIS G 3506:2004
- Table / clause
- Clauses 3 and 4, main-text Table 1, and notes
- PDF page references
- 4、5
- Unit
- Mass fraction (wt%)
- Analysis type
- Heat analysis
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | 0.79 ～ 0.86 |
| Si | 0.15 ～ 0.35 |
| Mn | 0.3 ～ 0.6 |
| P | ≤ 0.03 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
Applicability and limitations
JIS G 3506:2004: clause 3/4 and Table 1 of the English original list SWRH82A high-carbon steel wire rod. This record gives heat analysis, mass fraction wt%, from historical edition 2004, separately from edition 2024; current supply is not assumed. The note to Table 1 permits narrowing each end of the C range by 0.01 percentage points only by mutual agreement; the default range is not narrowed automatically. Clause 5.1: average total decarburization depth ≤0.20mm; inspection may be omitted unless specifically requested by the purchaser. Agreed special-quality, grain-size and inclusion requirements require separate verification. Wire rod under this standard is not automatically equivalent to cold-heading wire or a guarantee of finished-product properties.
Composition conditions
- Table 1 default C range as above; Narrowing of C upper and lower limits by 0.01 percentage points each is adopted only by mutual agreement.
- 5.1: mean total decarburization depth ≤0.20mm; this inspection may be omitted unless specifically requested by the buyer.
Verification notes
All 21 rows in original English JIS G 3506:2004, main-text Table 1 were checked cell by cellSWRH82A · POSCO wire rod catalogue (local archive 1203; original edition not stated)
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Carbon steel
- Subcategory
- Carbon steel
- Material form
- Wire rod
- Original record status
- Manufacturer source verified
- Document edition
- Local file 1203 (wire-rod pdf); the original does not state a publication edition; PDF metadata 2014-12-03 is only the file generation time
- Document title
- Wire rod
- Table / clause
- Printed page 15, composition table 2 (local table index)
- PDF page references
- 8
- Unit
- Percentages as stated in the original table; refer to the source for the specific basis
- Analysis type
- The catalog does not consistently specify heat or product analysis
- Manufacturer
- POSCO
Carbon-equivalent reference
Estimate from manufacturer-published ranges, not a standard guarantee or measured heat result; formula applicability requires review against the application and process.
Composition
| Element | Composition requirement |
|---|---|
| C | 0.79 ～ 0.86 |
| Si | 0.15 ～ 0.35 |
| Mn | 0.3 ～ 0.6 |
| P | ≤ 0.03 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
Applicability and limitations
POSCO local wire rod catalogue, PDF page 8
printed page 15, table index 1, row 19. The original edition number is not stated; the PDF creation date 2014-12-03 is not the standard publication year. Manufacturer range information does not constitute our supply guarantee. The original footnote permits reducing both C endpoints by 0.01 percentage points by purchaser-supplier agreement. The listed range is shown; this order adjustment is not applied automatically.
Composition conditions
- Original catalog chemical composition table %, wire rod; Editions of JIS/SAE/DIN were not provided; catalog data shall not be upgraded to the verified official editions of these standards.
- Dashes are not zero; cast/product analysis types are not consistently explicit. Orders, product-analysis deviations and actual supply require separate verification.
- The original footnote permits both the lower and upper C limits to be reduced by 0.01 percentage points by agreement between supplier and purchaser; The currently displayed table range is shown; this ordering adjustment is not automatically applied.
Verification notes
The original PDF tables and text coordinates were reconciled in both directions. Missing grade cells were restored; merged cells, footers and remarks were checked separately. Tables with identified disputes and rows without composition data are withheld.SWRH82A · Nippon Steel Wire Rods EXE203 2008.3 / JIS G3506-2004
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Carbon steel
- Subcategory
- Carbon steel
- Material form
- Wire rod
- Original record status
- Manufacturer source verified
- Document edition
- Cat. No. EXE203 2008.3 PDF; cover copyright 2008
- Document title
- Nippon Steel Wire Rods
- Table / clause
- Printed page 13, table index 3
- PDF page references
- 8
- Unit
- Mass fraction (%)
- Analysis type
- The original catalogue does not explicitly identify the analysis type for this table
- Manufacturer
- NIPPON STEEL CORPORATION
Carbon-equivalent reference
Estimate from manufacturer-published ranges, not a standard guarantee or measured heat result; formula applicability requires review against the application and process.
Composition
| Element | Composition requirement |
|---|---|
| C | 0.79 ～ 0.86 |
| Si | 0.15 ～ 0.35 |
| Mn | 0.3 ～ 0.6 |
| P | ≤ 0.03 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
Applicability and limitations
Historical Nippon Steel wire-rod catalogue EXE203 2008.3, PDF page 8
printed page 13, JIS G3506-2004. The original catalogue does not explicitly identify the analysis type for this table. Manufacturer range data, not guaranteed standard limits or heat-specific measurements; this does not establish supply by Creation Group. Condition: by agreement, the lower end of the C range may be raised by 0.01 percentage points and its upper end lowered by 0.01 percentage points; Displays the original table range; no automatic narrowing is applied.
Composition conditions
- Original catalogue mass percentages, historical manufacturer data from 2008.3; Referenced standard names and editions follow the original document; this does not establish that the official texts of those standards have been obtained and verified.
- A dash or blank must not be treated as 0; only chemical composition has been checked in this batch. Mechanical properties and actual supply require separate verification under the applicable conditions.
- By agreement, the lower end of the C range may be raised by 0.01 percentage points and its upper end lowered by 0.01 percentage points; Displays the original table range; no automatic narrowing is applied.
Verification notes
Grouped tables were expanded in full and checked against original images and notes. Ordinary, residual and conditional elements are kept separate; suffix tables lacking complete base-steel composition are excluded.SWRH82A · CHINA STEEL CORPORATION · Bars and Wire Rods Product Catalogue 2014-C1 / 7.1.6 JIS G3506 (Edition unspecified)
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Carbon steel
- Subcategory
- Carbon steel
- Material form
- Bars and wire rod
- Original record status
- Manufacturer source verified
- Document edition
- CAT.NO.3-BD-01-2014-C1 (stated on the back cover)
- Document title
- Bars and Wire Rods Product Catalogue
- Table / clause
- 7.1.6 JIS G3506 (Edition unspecified)
- PDF page references
- 14
- Unit
- Mass fraction (%)
- Analysis type
- The original catalogue does not explicitly identify the analysis type for this table
- Manufacturer
- CHINA STEEL CORPORATION
Carbon-equivalent reference
Estimate from manufacturer-published ranges, not a standard guarantee or measured heat result; formula applicability requires review against the application and process.
Composition
| Element | Composition requirement |
|---|---|
| C | 0.79 ～ 0.86 |
| Si | 0.15 ～ 0.35 |
| Mn | 0.3 ～ 0.6 |
| P | ≤ 0.03 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
Applicability and limitations
China Steel bar and wire-rod catalogue CAT.NO.3-BD-01-2014-C1, PDF page 14
printed page 12, 7.1.6 JIS G3506 (edition not stated). The original catalogue does not explicitly identify the analysis type for this table. Historical manufacturer range data, not guaranteed standard limits or heat-specific measurements; this does not establish supply by Creation Group. Condition: by agreement, both ends of the C range may be narrowed inward by 0.01 percentage points; The main table is retained for now.
Composition conditions
- Historical manufacturer 2014-C1 catalogue, bars/wire rod; Where the referenced standard edition is not identified, a year is not borrowed from another catalogue; a catalogue is not upgraded to the official standard text.
- A dash or blank must not be treated as zero. Composition data do not establish completeness or applicability of a formula; mechanical properties and supply require separate verification.
- By agreement, both ends of the C range may be narrowed inward by 0.01 percentage points; The main table is retained for now.
Verification notes
Merged cells in all 28 catalogue tables were reconstructed geometrically, with no missing cells. Original images, continuation pages and notes are recorded; disputed conditions are withheld.SWRH82A · JIS G 3506-1996
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Carbon steel
- Material form
- High-carbon steel wire rod
- Verification status
- Reference data; original source not verified
- Standard edition
- JIS G 3506—1996 (scanned Chinese translation)
- Table / clause
- Clause 2/3, Table 1, its continuation and notes
- PDF page references
- 1、2
- Unit
- Mass fraction (wt%)
- Analysis type
- Heat analysis (wording in the translation)
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | 0.79 ～ 0.86 |
| Si | 0.15 ～ 0.35 |
| Mn | 0.3 ～ 0.6 |
| P | ≤ 0.03 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
Applicability and limitations
JIS G 3506—1996: main-text Table 1 in a scanned Chinese translation lists SWRH82A high-carbon steel wire rod. The historical translation was checked row by row; the official Japanese original is still missing. Reference-review status is retained, without claiming original-source verification or current supply. Note to Table 1: narrowing each end of the C range by 0.01 percentage points requires agreement between purchaser and supplier. Clause 4.1: average total decarburization depth ≤0.20mm, but testing may be omitted unless requested by the purchaser. Grain-size and inclusion limits are subject to agreement.
Composition conditions
- Narrowing each C limit inward by 0.01 percentage points applies only by agreement; the default range is not narrowed.
- 4.1: mean total decarburization depth ≤0.20mm; inspection may be omitted unless requested by the buyer.