SUS436J1L
1 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for SUS436J1L →SUS436J1L · JIS G 4305-2021
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Stainless steel
- Subcategory
- Ferritic stainless steel
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- JIS G 4305-2021
- Table / clause
- Table 5 · Footnotes; 5.1/5.2
- PDF page references
- 7、10
- Unit
- Mass fraction (wt%)
- Analysis type
- Heat analysis, not product analysis
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Actual stabilizing element(s): Ti; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Actual stabilizing element(s): Nb; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Actual stabilizing element(s): Zr; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Actual stabilizing element(s): Ti+Nb; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Actual stabilizing element(s): Ti+Zr; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Actual stabilizing element(s): Nb+Zr; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Actual stabilizing element(s): Ti+Nb+Zr; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
IIW / CEV: not directly applicable to this material category
Pcm (Ito–Bessyo): not directly applicable to this material category
CET: not directly applicable to this material category
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| C | ≤ 0.025 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Ni | ≤ 0.6 (lower limit not stated) |
| Cr | 17 ～ 20 |
| Mo | 0.4 ～ 0.8 |
| N | ≤ 0.025 (lower limit not stated) |
Applicability and limitations
JIS G 4305:2021, Table 5, heat analysis, mass fractions wt%; Each actual edition is retained separately. Applicable to cold-rolled stainless steel plate, sheet and strip; this does not establish suitability for delivery as cold-heading wire or guarantee cold-heading process performance. 5.2 product analysis permits variations under JIS G0321, Table 5; unlisted items require agreement between the parties; Heat-analysis limits are not directly widened in this batch. A dash indicates that no general limit is specified and is not treated as 0; Conventional welding carbon-equivalent formulas for low-alloy steels do not apply to this stainless steel category. The original table permits one or a combination of Ti, Nb and Zr; The total of the actually selected elements is ≥8×(C+N) and ≤0.80%; The branch checks only measured values for the actual selected route; it does not invent independent lower and upper limits or treat unreported elements as 0.
Original condition-branch records
Actual stabilizing element(s): Ti; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.025 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Ni | ≤ 0.6 (lower limit not stated) |
| Cr | 17 ～ 20 |
| Mo | 0.4 ～ 0.8 |
| N | ≤ 0.025 (lower limit not stated) |
| Ti | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
- Combined limits
- Elements requiring measured values from the same heat
- Ti
- Combined-element limits
- Requirement
- Ti≥8(C+N)
- Element coefficient
- Ti
- 1
- C
- -8
- N
- -8
- Lower limit
- 0
- Limitations only; insufficient for a determination
- Yes
- Element-sum limits
- Elements concerned
- Ti
- Upper limit
- 0.8
Actual stabilizing element(s): Nb; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.025 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Ni | ≤ 0.6 (lower limit not stated) |
| Cr | 17 ～ 20 |
| Mo | 0.4 ～ 0.8 |
| N | ≤ 0.025 (lower limit not stated) |
| Nb | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
- Combined limits
- Elements requiring measured values from the same heat
- Nb
- Combined-element limits
- Requirement
- Nb≥8(C+N)
- Element coefficient
- Nb
- 1
- C
- -8
- N
- -8
- Lower limit
- 0
- Limitations only; insufficient for a determination
- Yes
- Element-sum limits
- Elements concerned
- Nb
- Upper limit
- 0.8
Actual stabilizing element(s): Zr; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.025 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Ni | ≤ 0.6 (lower limit not stated) |
| Cr | 17 ～ 20 |
| Mo | 0.4 ～ 0.8 |
| N | ≤ 0.025 (lower limit not stated) |
| Zr | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
- Combined limits
- Elements requiring measured values from the same heat
- Zr
- Combined-element limits
- Requirement
- Zr≥8(C+N)
- Element coefficient
- Zr
- 1
- C
- -8
- N
- -8
- Lower limit
- 0
- Limitations only; insufficient for a determination
- Yes
- Element-sum limits
- Elements concerned
- Zr
- Upper limit
- 0.8
Actual stabilizing element(s): Ti+Nb; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.025 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Ni | ≤ 0.6 (lower limit not stated) |
| Cr | 17 ～ 20 |
| Mo | 0.4 ～ 0.8 |
| N | ≤ 0.025 (lower limit not stated) |
| Ti | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
| Nb | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
- Combined limits
- Elements requiring measured values from the same heat
- Ti
- Nb
- Combined-element limits
- Requirement
- Ti+Nb≥8(C+N)
- Element coefficient
- Ti
- 1
- Nb
- 1
- C
- -8
- N
- -8
- Lower limit
- 0
- Limitations only; insufficient for a determination
- Yes
- Element-sum limits
- Elements concerned
- Ti
- Nb
- Upper limit
- 0.8
Actual stabilizing element(s): Ti+Zr; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.025 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Ni | ≤ 0.6 (lower limit not stated) |
| Cr | 17 ～ 20 |
| Mo | 0.4 ～ 0.8 |
| N | ≤ 0.025 (lower limit not stated) |
| Ti | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
| Zr | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
- Combined limits
- Elements requiring measured values from the same heat
- Ti
- Zr
- Combined-element limits
- Requirement
- Ti+Zr≥8(C+N)
- Element coefficient
- Ti
- 1
- Zr
- 1
- C
- -8
- N
- -8
- Lower limit
- 0
- Limitations only; insufficient for a determination
- Yes
- Element-sum limits
- Elements concerned
- Ti
- Zr
- Upper limit
- 0.8
Actual stabilizing element(s): Nb+Zr; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.025 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Ni | ≤ 0.6 (lower limit not stated) |
| Cr | 17 ～ 20 |
| Mo | 0.4 ～ 0.8 |
| N | ≤ 0.025 (lower limit not stated) |
| Nb | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
| Zr | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
- Combined limits
- Elements requiring measured values from the same heat
- Nb
- Zr
- Combined-element limits
- Requirement
- Nb+Zr≥8(C+N)
- Element coefficient
- Nb
- 1
- Zr
- 1
- C
- -8
- N
- -8
- Lower limit
- 0
- Limitations only; insufficient for a determination
- Yes
- Element-sum limits
- Elements concerned
- Nb
- Zr
- Upper limit
- 0.8
Actual stabilizing element(s): Ti+Nb+Zr; combined range from 8×(C+N) to 0.80%. Measured C/N and each selected element are required; missing values are not treated as 0.
| Element | Composition requirement |
|---|---|
| C | ≤ 0.025 (lower limit not stated) |
| Si | ≤ 1 (lower limit not stated) |
| Mn | ≤ 1 (lower limit not stated) |
| P | ≤ 0.04 (lower limit not stated) |
| S | ≤ 0.03 (lower limit not stated) |
| Ni | ≤ 0.6 (lower limit not stated) |
| Cr | 17 ～ 20 |
| Mo | 0.4 ～ 0.8 |
| N | ≤ 0.025 (lower limit not stated) |
| Ti | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
| Nb | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
| Zr | Combined total applies only to the selected stabilizing elements; no separate limits are specified. |
- Combined limits
- Elements requiring measured values from the same heat
- Ti
- Nb
- Zr
- Combined-element limits
- Requirement
- Ti+Nb+Zr≥8(C+N)
- Element coefficient
- Ti
- 1
- Nb
- 1
- Zr
- 1
- C
- -8
- N
- -8
- Lower limit
- 0
- Limitations only; insufficient for a determination
- Yes
- Element-sum limits
- Elements concerned
- Ti
- Nb
- Zr
- Upper limit
- 0.8