PSPC32B

1 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.

Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.

Open condition selection, comparison and carbon-equivalent tools for PSPC32B →

PSPC32B · POSCO wire rod catalogue (local archive 1203; original edition not stated)

Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results

Material category: Alloy steel
Subcategory: Alloy steel
Material form: Wire rod
Original record status: Manufacturer source verified
Document edition: Local file 1203 (wire-rod pdf); the original does not state a publication edition; PDF metadata 2014-12-03 is only the file generation time
Document title: Wire rod
Table / clause: Printed page 25, composition table 2 (local table index)
PDF page references: 13
Unit: Percentages as stated in the original table; refer to the source for the specific basis
Analysis type: The catalog does not consistently specify heat or product analysis
Manufacturer: POSCO

Carbon-equivalent reference

Estimate from manufacturer-published ranges, not a standard guarantee or measured heat result; formula applicability requires review against the application and process.

IIW / CEV：0.3900–0.4913Known-element contribution; incomplete value; missing Cr, Mo, V, Ni CEV = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15; an engineering estimate of welding cold-cracking susceptibility for carbon and low-alloy steels.

Pcm（Ito–Bessyo）：≥ 0.3275Known-element contribution; incomplete value; missing Cr, Ni, Mo, V; B has no specified upper limit; the carbon-equivalent upper bound cannot be determined Pcm = C + Si/30 + (Mn + Cu + Cr)/20 + Ni/60 + Mo/15 + V/10 + 5B; mainly used for low-carbon low-alloy steels, particularly modern low-carbon pipeline steels; more relevant when C is approximately no higher than 0.11%.

CET：0.3500–0.4310Known-element contribution; incomplete value; missing Mo, Cr, Ni CET = C + (Mn + Mo)/10 + (Cr + Cu)/20 + Ni/40; used in welding preheat assessment for ferritic steels, subject to the applicability conditions of EN 1011-2.

Composition

Element	Composition requirement
C	0.29 ～ 0.34
Si	0.15 ～ 0.35
Mn	0.6 ～ 0.9
P	≤ 0.035 (lower limit not stated)
S	≤ 0.03 (lower limit not stated)
Cu	≤ 0.02 (lower limit not stated)
B	≥ 0.0005 (upper limit not stated)

Applicability and limitations

POSCO local wire rod catalogue, PDF page 13

printed page 25, table index 1, row 3. The original edition number is not stated; the PDF creation date 2014-12-03 is not the standard publication year. Manufacturer range information does not constitute our supply guarantee. Original B minimum 5ppm; 1%=10000ppm. Units converted without changing the one-sided limit.

Composition conditions

Original catalog chemical composition table %, wire rod; Editions of JIS/SAE/DIN were not provided; catalog data shall not be upgraded to the verified official editions of these standards.
Dashes are not zero; cast/product analysis types are not consistently explicit. Orders, product-analysis deviations and actual supply require separate verification.
Original B value: 5ppm Min.; 1%=10000ppm, converted according to units, single-sided limits remain unchanged.

Verification notes

The original PDF tables and text coordinates were reconciled in both directions. Missing grade cells were restored; merged cells, footers and remarks were checked separately. Tables with identified disputes and rows without composition data are withheld.