NICR19FE19NB5MO3
8 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for NICR19FE19NB5MO3 →NiCr19Fe19Nb5Mo3 · EN 10269-2013
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- EN 10269-2013
- Table / clause
- Table1 final page: nickel alloys and combined niobium-tantalum requirements
- PDF page references
- 19
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| C | 0.02 ～ 0.08 |
| Si | ≤ 0.035 (lower limit not stated) |
| Mn | ≤ 0.035 (lower limit not stated) |
| P | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Al | 0.3 ～ 0.7 |
| B | 0.002 ～ 0.006 |
| Cr | 17.0 ～ 21.0 |
| Mo | 2.8 ～ 3.3 |
| Ni | 50.0 ～ 55.0 |
| Cu | ≤ 0.3 (lower limit not stated) |
| Co | ≤ 1.0 (lower limit not stated) |
| Nb | 4.7 ～ 5.5 |
| Ti | 0.6 ～ 1.2 |
Applicability and limitations
Table 1 (final table page, PDF19) in the official BS English-language adoption of EN10269:2013; heat-analysis mass fractions wt%. ; Nb+Ta is a combined constraint; when individual Nb/Ta ranges are not specified, they shall not be split into independent standard limits; Reverse lookup requires the input of all relevant elements. ; Ni≥65 or Ni≥70 are lower limits only, with no independent standard upper limit; Do not automatically fill in a range. ; For NiCr19Fe19Nb5Mo3, Si/Mn are each ≤.035% in the original table and are retained as per the original text; Fe is the balance; no independent numerical range is provided. ; Unlisted elements are not entered as zero; Properties, heat treatment, product analysis, and cold heading supply suitability shall be verified separately.
Verification notes
Official English Table 1 and footnotes were visually checked; combined niobium-tantalum requirements are retainedNiCr19Fe19Nb5Mo3 · DIN 17744-2002
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Nickel and nickel alloys
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Al | 0.3 ～ 0.7 |
| B | ≤ 0.006 (lower limit not stated) |
| C | 0.02 ～ 0.08 |
| Co | ≤ 1 (lower limit not stated) |
| Cr | 17 ～ 21 |
| Cu | ≤ 0.3 (lower limit not stated) |
| Mn | ≤ 0.35 (lower limit not stated) |
| Mo | 2.8 ～ 3.3 |
| Ni | 50 ～ 55 |
| P | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 0.35 (lower limit not stated) |
| Ti | 0.6 ～ 1.2 |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
NiCr19Fe19Nb5Mo3 · DIN 17744-2020
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Nickel and nickel alloys
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Al | 0.3 ～ 0.7 |
| B | ≤ 0.006 (lower limit not stated) |
| C | 0.02 ～ 0.08 |
| Co | ≤ 1 (lower limit not stated) |
| Cr | 17 ～ 21 |
| Cu | ≤ 0.3 (lower limit not stated) |
| Mn | ≤ 0.35 (lower limit not stated) |
| Mo | 2.8 ～ 3.3 |
| Ni | 50 ～ 55 |
| P | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 0.35 (lower limit not stated) |
| Ti | 0.6 ～ 1.2 |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
NiCr19Fe19Nb5Mo3 · DIN 17750-2002
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Nickel and nickel alloys
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Al | 0.3 ～ 0.7 |
| B | ≤ 0.006 (lower limit not stated) |
| C | 0.02 ～ 0.08 |
| Co | ≤ 1 (lower limit not stated) |
| Cr | 17 ～ 21 |
| Cu | ≤ 0.3 (lower limit not stated) |
| Mn | ≤ 0.35 (lower limit not stated) |
| Mo | 2.8 ～ 3.3 |
| Ni | 50 ～ 55 |
| P | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 0.35 (lower limit not stated) |
| Ti | 0.6 ～ 1.2 |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
NiCr19Fe19Nb5Mo3 · DIN 17752-2002
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Nickel and nickel alloys
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Al | 0.3 ～ 0.7 |
| B | ≤ 0.006 (lower limit not stated) |
| C | 0.02 ～ 0.08 |
| Co | ≤ 1 (lower limit not stated) |
| Cr | 17 ～ 21 |
| Cu | ≤ 0.3 (lower limit not stated) |
| Mn | ≤ 0.35 (lower limit not stated) |
| Mo | 2.8 ～ 3.3 |
| Ni | 50 ～ 55 |
| P | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 0.35 (lower limit not stated) |
| Ti | 0.6 ～ 1.2 |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
NiCr19Fe19Nb5Mo3 · EN 10302-2008
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Nickel and nickel alloys
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Al | 0.3 ～ 0.7 |
| B | 0.002 ～ 0.006 |
| C | 0.02 ～ 0.08 |
| Co | ≤ 1 (lower limit not stated) |
| Cr | 17 ～ 21 |
| Cu | ≤ 0.3 (lower limit not stated) |
| Mn | ≤ 0.35 (lower limit not stated) |
| Mo | 2.8 ～ 3.3 |
| Ni | 50 ～ 55 |
| P | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 0.35 (lower limit not stated) |
| Ti | 0.6 ～ 1.2 |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
NiCr19Fe19Nb5Mo3 · GB /T 26030-2010
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Alloy steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Al | 0.2 ～ 0.8 |
| B | ≤ 0.006 (lower limit not stated) |
| C | ≤ 0.08 (lower limit not stated) |
| Co | ≤ 1.5 (lower limit not stated) |
| Cr | 17 ～ 21 |
| Cu | ≤ 0.3 (lower limit not stated) |
| Mn | ≤ 0.4 (lower limit not stated) |
| Mo | 2.8 ～ 3.3 |
| P | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 0.4 (lower limit not stated) |
| Ti | 0.6 ～ 1.2 |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.
NiCr19Fe19Nb5Mo3 · ISO 4955-2016
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Alloy steel
- Material form
- Reference record
- Verification status
- Reference data; original source not verified
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Al | 0.3 ～ 0.7 |
| B | 0.002 ～ 0.006 |
| C | 0.02 ～ 0.08 |
| Co | ≤ 1 (lower limit not stated) |
| Cr | 17 ～ 21 |
| Cu | ≤ 0.3 (lower limit not stated) |
| Mn | ≤ 0.35 (lower limit not stated) |
| Mo | 2.8 ～ 3.3 |
| Ni | 50 ～ 55 |
| P | ≤ 0.015 (lower limit not stated) |
| S | ≤ 0.015 (lower limit not stated) |
| Si | ≤ 0.35 (lower limit not stated) |
| Ti | 0.6 ～ 1.2 |
Applicability and limitations
A match in the materials database does not establish suitability for cold heading or guarantee finished-product strength. Confirmation must consider wire condition, deformation, heat treatment and tests on actual parts.