INCOLOY 800HT
4 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for INCOLOY 800HT →Incoloy 800HT · Alloy Wire International manufacturer catalogue (edition not stated)
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Nickel and nickel alloys
- Subcategory
- Nickel and nickel alloys
- Material form
- Wire
- Composition basis
- Manufacturer typical composition range
- Original record status
- Manufacturer source verified
- Document edition
- The original text does not specify the publication version; PDF metadata 2015-07-22 only records the generation date
- Document title
- AWBrochure manufacturer product catalogue
- Table / clause
- Approximate chemical composition
- PDF page references
- 12
- Unit
- Percentages as stated in the original table; refer to the source for the specific basis
- Analysis type
- Manufacturer approximate composition, not measured heat or product analysis
- Manufacturer
- Alloy Wire International
Carbon-equivalent reference
Estimate from manufacturer-published ranges, not a standard guarantee or measured heat result; formula applicability requires review against the application and process.
Composition
| Element | Composition requirement |
|---|---|
| Ni | 30.0 ～ 35.0 |
| Fe | ≥ 39.5 (upper limit not stated) |
| Cr | 19.0 ～ 23.0 |
| C | 0.06 ～ 0.1 |
| Al | 0.15 ～ 0.6 |
| Ti | 0.15 ～ 0.6 |
Applicability and limitations
Alloy Wire International original catalogue, PDF page 12
printed page 11. Original publication edition not stated; metadata 2015-07-22 is not an edition. Approximate chemical composition: manufacturer approximate composition, single values are approximate, BAL means balance. Neither standard guaranteed values nor measured heat analysis; does not establish supply by our company. Display only; excluded from standard-limit reverse search. Only the total Al+Ti is specified; do not split it into individual element limits.
Composition conditions
- The original text explicitly labels the entire column as APPROXIMATE CHEMICAL COMPOSITION, not delivery guarantee limits.
- Single values shall be saved as nominal and marked as approximate values; do not set min=max; BAL shall not be calculated as a number or treated as 0; Shall not be used for standard limit reverse-lookup.
- IIW/Pcm/CET are not applied to this batch of nickel-based/high-alloy/stainless/copper/titanium materials; Material application and manufacturer supply capability still require verification.
- Only the combined Al+Ti content is specified; do not split it into individual element limits.
Combined limits
- Combined-element limits
- Requirement
- Al + Ti
- Element coefficient
- Al
- 1
- Ti
- 1
- Lower limit
- 0.85
- Upper limit
- 1.2
- Elements requiring measured values from the same heat
- Ti
- Al
Verification notes
All 47 grade compositions were checked against original images; nominal values, one-sided limits, ranges, BAL balance and totals remain separate.INCOLOY 800 HT · Alloy Wire technical catalogue (AW_Tech-broch_v6 archive; internal edition not stated)
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Nickel and nickel alloys
- Subcategory
- Nickel and nickel alloys
- Material form
- Wire
- Original record status
- Manufacturer source verified
- Document edition
- Internal publication number not specified; Filename v6 and metadata 2020-03-04 only record file information and shall not be used to infer the official edition
- Document title
- AW_Tech-broch_v6 technical catalogue archive
- Table / clause
- Chemical composition (minimum % / maximum %)
- PDF page references
- 38
- Unit
- Percentages as stated in the original table; refer to the source for the specific basis
- Analysis type
- Manufacturer composition table; heat or product analysis not specified
- Manufacturer
- Alloy Wire International
Carbon-equivalent reference
Estimate from manufacturer-published ranges, not a standard guarantee or measured heat result; formula applicability requires review against the application and process.
Composition
| Element | Composition requirement |
|---|---|
| Ni | 30.0 ～ 35.0 |
| Co | ≤ 2.0 (lower limit not stated) |
| Cu | ≤ 0.75 (lower limit not stated) |
| Cr | 19.0 ～ 23.0 |
| Al | 0.15 ～ 0.6 |
| C | 0.05 ～ 0.1 |
| Si | ≤ 1.0 (lower limit not stated) |
| Mn | ≤ 1.5 (lower limit not stated) |
| Ti | 0.15 ～ 0.6 |
| Fe | Balance (BAL; numerical range not stated) |
| S | ≤ 0.015 (lower limit not stated) |
Applicability and limitations
Alloy Wire technical catalogue AW_Tech-broch_v6 archive, PDF/printed page 38. Internal publication edition not stated; metadata 2020-03-04 is not an edition. The original chemical-composition table gives minimum %/maximum %; nominal single values are separately marked approximate, BAL means balance. Separately cited standards are unverified; these are neither standard guaranteed values nor measured heat analysis and do not establish supply by our company. Display only; excluded from standard-limit reverse search. The heading and minimum/maximum columns belong to this table; values are not mixed with a similar short table. Original Nb/Cb marks are retained for the same element, niobium, not total Nb+Ta; separately listed Ta remains independent.
Composition conditions
- Original table from manufacturer technical catalog; The editions of separately referenced standards have not been verified; these are neither standard guarantee values nor measured heat results.
- Nominal values are saved as nominal; min=max is not set; BAL balance is not calculated as a number; The current complete catalog is for reference only and shall not be used for standard limit reverse-lookup.
- The title of this table is Chemical Composition, Min %/Max %; Shall not be mixed with values from another similar summary table.
- The original Nb/Cb notation is retained; both denote the same element, niobium; Not Nb+Ta total; Ta is independent where listed separately.
Verification notes
A batch manufacturer-code pairing and difference check covered 58 composition tables against 47 older records. New entries and dynamic/alternative/residual clauses were checked against original images; changes reconciled cell by cell with the original PDF’s structured ledger. The 45 linked and 13 independent entries remain separate.Incoloy 800HT · No corresponding standard is provided
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Special alloy steel
- Material form
- Reference record
- Composition basis
- Manufacturer-published composition range
- Verification status
- Reference data; original source not verified
- Document title
- Technical Bulletin SMC-047 September2004
- Table / clause
- Table1 General Requirements — 800HT
- PDF page references
- 2
- Manufacturer
- Special Metals
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Ni | 30 ～ 35 |
| Cr | 19 ～ 23 |
| Fe | ≥ 39.5 (upper limit not stated) |
| C | 0.06 ～ 0.1 |
| Al | 0.25 ～ 0.6 |
| Ti | 0.25 ～ 0.6 |
Applicability and limitations
General composition requirements for manufacturer data; Al and Ti must simultaneously satisfy the individual element range and the combined range. Special orders may specify stricter composition or grain size; general conditions shall not be treated as guarantees for all orders. An 800H designation alone does not establish conformity to 800HT; their C/Al/Ti requirements differ.. Only a lower limit of 39.5% is given for Fe; elements not listed in this table shall not be filled as zero.
Combined limits
- Combined-element limits
- Requirement
- Al + Ti
- Element coefficient
- Al
- 1
- Ti
- 1
- Lower limit
- 0.85
- Upper limit
- 1.2
Verification notes
Composition from official manufacturer information; Specific product standards and supply requirements require separate verificationIncoloy 800HT · No corresponding standard is provided
Original-source verification is incomplete; this is not a formal standard reference
- Material category
- Stainless steel
- Subcategory
- Special alloy steel
- Material form
- Reference record
- Composition basis
- Manufacturer-published composition range
- Verification status
- Reference data; original source not verified
- Document title
- Technical Bulletin SMC-047 September2004
- Table / clause
- Table1 General Requirements — 800HT
- PDF page references
- 2
- Manufacturer
- Special Metals
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Ni | 30 ～ 35 |
| Cr | 19 ～ 23 |
| Fe | ≥ 39.5 (upper limit not stated) |
| C | 0.06 ～ 0.1 |
| Al | 0.25 ～ 0.6 |
| Ti | 0.25 ～ 0.6 |
Applicability and limitations
General composition requirements for manufacturer data; Al and Ti must simultaneously satisfy the individual element range and the combined range. Special orders may specify stricter composition or grain size; general conditions shall not be treated as guarantees for all orders. An 800H designation alone does not establish conformity to 800HT; their C/Al/Ti requirements differ.. Only a lower limit of 39.5% is given for Fe; elements not listed in this table shall not be filled as zero.
Combined limits
- Combined-element limits
- Requirement
- Al + Ti
- Element coefficient
- Al
- 1
- Ti
- 1
- Lower limit
- 0.85
- Upper limit
- 1.2