HSI62-0.6
4 source records. Standards, editions and conditions are presented separately; matching grade names do not establish interchangeability.
Refer to each source for mass fractions and analysis type. Missing values are not treated as 0. Manufacturer typical values, standard guarantees and measured heat results must remain separate. Use the material selector for calculations and condition selection.
Open condition selection, comparison and carbon-equivalent tools for HSI62-0.6 →HSi62-0.6 · GB /T 5231-2012
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Copper and copper alloys
- Subcategory
- Copper and copper alloys
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- GB/T 5231-2012
- Table / clause
- Table 3 · Footnotes
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 3 default Fe≤0.15%
Specified nonmagnetic application, Fe≤0.030%
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| Cu | 59 ～ 64 |
| Fe | ≤ 0.15 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1 |
| Sn | ≤ 0.6 (lower limit not stated) |
| Zn | Balance |
Applicability and limitations
Composition, mass fractions wt%; A single value is a maximum; ranges are retained as in the original table. ; The balance is not converted into a fixed numerical value or treated as zero; Unlisted elements are not treated as zero. ; Steel IIW/Pcm/CET carbon-equivalent formulas are not directly applied to copper or copper alloys. ; Zn is the balance; Total impurities ≤2.0%. Fe column, note a: nonmagnetic-brass condition Fe≤0.030% applies only to specified nonmagnetic applications.
Original condition-branch records
Table 3 default Fe≤0.15%
| Element | Composition requirement |
|---|---|
| Cu | 59 ～ 64 |
| Fe | ≤ 0.15 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1 |
| Sn | ≤ 0.6 (lower limit not stated) |
| Zn | Balance |
Specified nonmagnetic application, Fe≤0.030%
| Element | Composition requirement |
|---|---|
| Cu | 59 ～ 64 |
| Fe | ≤ 0.03 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1 |
| Sn | ≤ 0.6 (lower limit not stated) |
| Zn | Balance |
A condition branch must be selected
YesVerification notes
The original Table 3/5 and footnotes have been checkedHSi62-0.6 · GB /T 5231-2022
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Copper and copper alloys
- Subcategory
- Copper and copper alloys
- Material form
- Reference record
- Original record status
- Historical-edition reference
- Standard edition
- GB/T 5231-2012
- Table / clause
- Table 3 · Footnotes
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 3 default Fe≤0.15%
Specified nonmagnetic application, Fe≤0.030%
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| Cu | 59 ～ 64 |
| Fe | ≤ 0.15 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1 |
| Sn | ≤ 0.6 (lower limit not stated) |
| Zn | Balance |
Applicability and limitations
The chemical composition currently shown is transcribed from the original GB /T 5231-2012; The original record cites GB /T 5231-2022; that original edition remains unavailable, and differences between editions have not been confirmed. Composition, mass fractions wt%; A single value is a maximum; ranges are retained as in the original table. ; The balance is not converted into a fixed numerical value or treated as zero; Unlisted elements are not treated as zero. ; Steel IIW/Pcm/CET carbon-equivalent formulas are not directly applied to copper or copper alloys. ; Zn is the balance; Total impurities ≤2.0%. Fe column, note a: nonmagnetic-brass condition Fe≤0.030% applies only to specified nonmagnetic applications.
Original condition-branch records
Table 3 default Fe≤0.15%
| Element | Composition requirement |
|---|---|
| Cu | 59 ～ 64 |
| Fe | ≤ 0.15 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1 |
| Sn | ≤ 0.6 (lower limit not stated) |
| Zn | Balance |
Specified nonmagnetic application, Fe≤0.030%
| Element | Composition requirement |
|---|---|
| Cu | 59 ～ 64 |
| Fe | ≤ 0.03 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1 |
| Sn | ≤ 0.6 (lower limit not stated) |
| Zn | Balance |
A condition branch must be selected
YesVerification notes
The chemical composition currently shown is transcribed from the original GB /T 5231-2012; The original record cites GB /T 5231-2022; that original edition remains unavailable, and differences between editions have not been confirmed.HSi62-0.6 · GB /T 5231-2022
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Copper and copper alloys
- Subcategory
- Copper and copper alloys
- Material form
- Reference record
- Original record status
- Historical-edition reference
- Standard edition
- GB/T 5231-2012
- Table / clause
- Table 3 · Footnotes
Carbon-equivalent reference
Estimates are presented separately for each applicable composition condition. Match the actual ordering conditions; ranges must not be combined.
Table 3 default Fe≤0.15%
Specified nonmagnetic application, Fe≤0.030%
Composition record (conditional branches apply; this is not an unconditional requirement)
| Element | Composition requirement |
|---|---|
| Cu | 59 ～ 64 |
| Fe | ≤ 0.15 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1 |
| Sn | ≤ 0.6 (lower limit not stated) |
| Zn | Balance |
Applicability and limitations
The chemical composition currently shown is transcribed from the original GB /T 5231-2012; The original record cites GB /T 5231-2022; that original edition remains unavailable, and differences between editions have not been confirmed. Composition, mass fractions wt%; A single value is a maximum; ranges are retained as in the original table. ; The balance is not converted into a fixed numerical value or treated as zero; Unlisted elements are not treated as zero. ; Steel IIW/Pcm/CET carbon-equivalent formulas are not directly applied to copper or copper alloys. ; Zn is the balance; Total impurities ≤2.0%. Fe column, note a: nonmagnetic-brass condition Fe≤0.030% applies only to specified nonmagnetic applications.
Original condition-branch records
Table 3 default Fe≤0.15%
| Element | Composition requirement |
|---|---|
| Cu | 59 ～ 64 |
| Fe | ≤ 0.15 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1 |
| Sn | ≤ 0.6 (lower limit not stated) |
| Zn | Balance |
Specified nonmagnetic application, Fe≤0.030%
| Element | Composition requirement |
|---|---|
| Cu | 59 ～ 64 |
| Fe | ≤ 0.03 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1 |
| Sn | ≤ 0.6 (lower limit not stated) |
| Zn | Balance |
A condition branch must be selected
YesVerification notes
The chemical composition currently shown is transcribed from the original GB /T 5231-2012; The original record cites GB /T 5231-2022; that original edition remains unavailable, and differences between editions have not been confirmed.HSi62-0.6 · GB/T 5231-2012
Chemical composition source verified; this does not verify every standard clause, actual supply or measured heat results
- Material category
- Copper and copper alloys
- Material form
- Reference record
- Original record status
- Original standard verified
- Standard edition
- GB/T 5231-2012
- Table / clause
- Table 3, row 66, designation C68350
- PDF page references
- 9
- Unit
- Mass fraction (wt%)
Carbon-equivalent reference
Composition
| Element | Composition requirement |
|---|---|
| Cu | 59.0 ～ 64.0 |
| Fe | ≤ 0.15 (lower limit not stated) |
| Pb | ≤ 0.09 (lower limit not stated) |
| Al | ≤ 0.3 (lower limit not stated) |
| P | 0.05 ～ 0.4 |
| Ni | ≤ 0.2 (lower limit not stated) |
| Si | 0.3 ～ 1.0 |
| Sn | ≤ 0.6 (lower limit not stated) |
Applicability and limitations
Mass fraction wt%; GB/T 5231-2012, Table 3, row 66, designation C68350; scanned PDF, PDF physical page 9. Zn is balance; dashes mean unspecified and are not replaced with zero. Clause 2.2: single impurity values in the table are maxima. The total of table-listed impurities is ≤2% and must be checked against measured values for the impurity elements specified in the standard. This standard provides the grade-composition basis for wrought copper and copper alloys; actual supply and cold-heading suitability require separate confirmation.
Combined limits
- Combined-element limits
- Elements requiring measured values from the same heat