化学成分来源与适用范围
以下为所列标准版本的参考成分,非炉批实测;订单适用标准、原料与成品要求须分别确认。
25CrMoS4 · ISO 4954:2018
| 元素 | 质量分数 / % |
|---|---|
| C | 0.22–0.29 |
| Si | ≤0.3 |
| Mn | 0.6–0.9 |
| P | ≤0.025 |
| S | 0.02–0.04 |
| Cr | 0.9–1.2 |
| Mo | 0.15–0.3 |
| Cu | ≤0.25 |
来源: ISO 4954:2018




1.交货条件的组合
表C.1交货时热处理条件的组合、产品形式和适用要求
2.化学组成
化学成分来源与适用范围
以下为所列标准版本的参考成分,非炉批实测;订单适用标准、原料与成品要求须分别确认。
来源: ISO 4954:2018 · Table C.2 · 25CrMoS4 · p.41
Single values are maxima unless indicated otherwise; unlisted elements and blank cells are not assumed zero. Alternative limits, optional additions and analysis tolerances require the relevant table notes and order agreement. This reference table does not replace the complete standard.
除非另有说明,单个数值均为最大值;未列出的元素及空白单元格不按零处理。备选限值、可选添加物及分析公差需参照相关表格注释并经订单约定。本参考表不能替代完整标准。
3.力学性能
表C.5-不含硼合金钢牌号的力学性能
| Steel name | Diameter | Delivery condition | ||||||
|---|---|---|---|---|---|---|---|---|
| +AC or +AC+PE | +AC+C+AC | +AC+C+AC+LC | ||||||
| above mm | up to mm | Rm max. MPa | Z min % | Rm max. MPa | Z min. % | Rm max. MPa | Z min. % | |
| 25CrMo4 25CrMoS4 | 2 | 5 | 570 | 62 | 610 | 60 | ||
| 5 | 40 | 580 | 60 | 560 | 62 | 600 | 60 | |
4.淬透性要求
表C.7-具有规定 (正常) 淬透性的不含硼的钢种的硬度限值 (H级)
| Steel name | Sym- bol | Austenitizing temperature °℃±5℃ | Limits of range | Hardness HRC at a distance from quenched end of test piece(in mm) of | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 13 | 15 | 20 | 25 | 30 | ||||
| 25CrMoS4 | min. | 44 | 43 | 40 | 37 | 34 | 32 | 29 | 27 | 23 | 21 | 20 | — | — | — | — | |||
表C.9-淬透性受限的无硼钢种的硬度限值散射带 (HH和HL等级) a
| Steel name | Symbol | Austenitizing temperature ℃±5℃ | Limits of range | Hardness HRC at a distance from quenched end of test piece(in mm) of | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1,5 | 3 | 5 | 7 | 9 | 11 | 13 | 15 | 20 | 25 | 30 | 35 | 40 | 45 | 50 | ||||
| 25CrMo4 25CrMoS4 | +HH | 850 | max. | 52 | 52 | 51 | 50 | 48 | 46 | 43 | 41 | 37 | 35 | 33 | 32 | 31 | 31 | 31 |
| min. | 47 | 46 | 44 | 41 | 39 | 37 | 34 | 32 | 28 | 26 | 24 | 23 | 22 | 22 | 22 | |||
| +HL | max. | 49 | 49 | 47 | 46 | 43 | 41 | 38 | 36 | 32 | 30 | 29 | 28 | 27 | 27 | 27 | ||
| min. | 44 | 43 | 40 | 37 | 34 | 32 | 29 | 27 | 23 | 21 | 20 | — | — | |||||
| min. | 53 | 53 | 53 | 53 | 52 | 51 | 51 | 51 | 51 | 50 | 50 | 50 | 50 | 49 | 48 | |||
| min | 50 | 50 | 50 | 50 | 49 | 48 | 48 | 48 | 48 | 47 | 47 | 47 | 46 | 45 | 44 | |||
| This table is not applicable to steels ordered with a restricted range of carbon content,see footnote c)in Table C.2. | ||||||||||||||||||
表C.10-芯部硬度试验中至少应获得90% 马氏体的最大直径 (+ CH等级)
| Steel name | Symbol | Austenitizing temperature in the core hardening testa C±5℃ | Min.core hardness ( 90 %martensite structure) HRC | Maximum diameter to ensure 90 %of martensite in the coreb mm |
|---|---|---|---|---|
| 25CrMoS4 | +CH | 850 | 41 | 13 |
| a As a guideline,a hardening time at temperature of at least 30 min is recommended. The maximum diameters stated are those attainable with the lowest hardenability within each steel grade.Using +HH grades the maximum diameter can be increased. | ||||
